Loading ...
Loading ...
Loading ...
stereos require a software update to enable this functionality of
the remote.
NOTE: When you connect to a stereo, all zones are selected by
default.
1
Press and to enter zone selection mode.
The status LED begins flashing green.
2
Press a button to make a selection:
• Press for zone 1.
• Press for zone 2.
• Press for zone 3.
• Press for zone 4.
• Press for all zones.
• Press to cancel the zone selection.
When a zone is selected successfully, the status LED turns
on green briefly and then turns off. When zone selection fails,
times out, or is canceled, the status LED turns on red briefly
and then turns off.
NOTE: When you select an inactive or invalid zone, the remote
still functions but does not control the volume. You can select
to select all zones.
Replacing the Battery
The remote uses one CR2032 lithium coin-cell battery.
1
Rotate the remote control, and remove it from the mount.
2
Rotate the battery compartment counter-clockwise until the
line points to .
3
Wrap the end of a small flat screwdriver with tape.
The tape protects the battery, battery compartment, and
contacts from damage.
4
Carefully pry the battery from the battery compartment.
5
Insert the new battery into the compartment with the positive
side facing down.
NOTE: Do not damage or lose the O-ring gasket.
6
Align the battery compartment in the remote control so the
line points to .
7
Press the battery compartment down into the remote control,
and rotate the compartment clockwise until the line points to
.
8
Make sure the battery compartment is fully seated in the
remote control.
9
Place the remote control in the mount, and rotate until it
clicks.
Remote Specifications
Weight With mount: 30 g (1.6 oz.)
Without mount: 25 g (0.88 oz.)
Battery type User-replaceable CR2032 (3 V)
Battery life (typical use) At least 3 years
Operating temperature range From 0° to 50°C (from 32° to 122°F)
Storage temperature range From -20° to 70°C (from -4° to 158°F)
Radio frequency/protocol 2.4 GHz @ 6.42 dBm nominal
ANT wireless range Up to 10 m (33 ft.)
Compass-safe distance 5 cm
Water rating IEC 60529 IPX6 and IPX7
1
Troubleshooting
The remote will not connect to the stereo
• Make sure the stereo is in Bluetooth discoverable mode.
• Move closer to the stereo, and attempt to connect to it again
(Connecting the ARX70 Remote to a Stereo, page 1).
• Disable Bluetooth discoverable mode on the stereo, and then
re-enable it.
The LED does not light when I press a button
The battery is low or dead or is installed improperly. Replace the
battery (Replacing the Battery, page 2).
The LED is only red or orange when I press a button
• Move closer to the stereo, and attempt to connect to it again
(Connecting the ARX70 Remote to a Stereo, page 1).
• Before mounting, make sure you have selected an optimal
location for the remote (Mounting Considerations, page 1).
The remote does not change the volume, but other
functionality works
An invalid zone is selected. Select a zone valid for the stereo
(Selecting a Zone, page 1).
物質宣言
部件名称 有毒有害物质或元素
铅 汞 镉 六价铬 多溴联苯 多溴二苯醚
印刷电路板组件 X O O O O O
金属零件 X O O O O O
电池 O O O O O O
1
Withstands incidental exposure to water of up to 1 m for up to 30 min. and is protected against powerful jets of water. For
more information go to garmin.com/waterrating.
2 Replacing the Battery
Loading ...
Loading ...
Loading ...