Loading ...
Loading ...
Loading ...
Remote Overview
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Radio sources: Press to tune to the previous station.
Other sources: Press to skip to the beginning of the track or
to the previous track.
Radio sources: Press to tune to the next station.
Other sources: Press to skip to the next track.
Press to decrease the volume.
Hold to quickly decrease the volume.
Press to increase the volume.
Hold to quickly increase the volume.
and Press both keys to enter zone selection mode (Selecting a
Zone, page 1).
Press to cycle through the available sources.
Hold to pair with a stereo (Connecting the ARX70 Remote to
a Stereo, page 1).
Radio sources: Press to mute or un-mute.
Other sources: Press to pause or resume.
Status LEDs
Green short blink Transmission successful
Green long blink Pairing or zone selection successful
Green flashing In zone selection mode
Green and red flashing In pairing mode
Red short blink Transmission failed
Red long blink Pairing or zone selection failed
Orange flashing Attempting to transmit; check the stereo
Connecting the ARX70 Remote to a
Stereo
For a list of compatible stereos, go to
www.fusionentertainment.com/marine/products/remote-controls
/MS-ARX70B/specs.
1
Bring the ARX70 remote within 10 m (33 ft.) of the compatible
stereo.
NOTE: Stay 10 m (33 ft.) away from other ANT
®
devices
while pairing.
2
Place the stereo into Bluetooth
®
discoverable mode.
For detailed information, see the stereo owner's manual at
www.fusionentertainment.com/marine.
3
On the ARX70 remote, press and hold until the status LED
starts alternating green and red.
The remote searches for the stereo. When the remote pairs
successfully, the status LED turns on green briefly and then
turns off.
If the remote cannot find the stereo, the status LED turns on red
briefly and then turns off.
Mounting Considerations
NOTICE
Selecting the correct mounting location is critical to optimize the
performance of the remote control.
• You must mount the remote control in a location that is within
10 m (33 ft.) of the stereo.
• You must mount the remote control in a location where it is
not submerged.
• If you need to mount the remote control outside the boat, you
should mount it in a location where it will not be damaged by
docks, pilings, or other pieces of equipment.
• You should select a flat mounting surface for the best results.
• The mounting surface must be free of dirt, debris, wax, or
coatings.
• After you select the location, hold the remote control in the
selected location, press a few buttons, and confirm the
operation on the stereo.
• Move away from sources that can interfere with the remote
control's operation. Sources of interference may include
strong electromagnetic fields, some 2.4 GHz wireless
sensors, high-voltage power lines, electric motors, ovens,
microwave ovens, 2.4 GHz cordless phones, and wireless
LAN access points.
Mounting the Remote Control
Before mounting the remote, you must connect the remote to
the stereo (Connecting the ARX70 Remote to a Stereo, page 1).
1
Select an appropriate location for the remote control
(Mounting Considerations, page 1).
2
Thoroughly clean and dry the mounting surface using a
mixture of water and isopropyl alcohol.
The mounting surface must be free of dirt, debris, wax, or
coatings.
3
Test the range at the selected location by holding the remote
at the location, pressing a few buttons, and confirming the
operation.
4
Place the remote control on the mount, and rotate the remote
until you hear a click.
5
Remove the backing from the adhesive.
6
Carefully orient the remote control in the mount with the
FUSION
®
logo at the bottom.
NOTICE
Before placing the adhesive on the mounting surface, make
sure the location and orientation are correct. It is extremely
difficult to remove the adhesive. Some mounting surfaces
might be damaged after removing the adhesive.
7
Press the remote control firmly onto the mounting surface,
maintaining pressure for at least 60 seconds.
8
Allow the remote control to sit at room temperature for 72
hours.
Selecting a Zone
On compatible stereos, you can use the ARX70 remote control
to select a zone and change the volume of the zone. Some
Remote Overview 1
Loading ...
Loading ...
Loading ...