Loading ...
Loading ...
Loading ...
6
NOTE: If you open the dryer door prior to the end of the
Wrinkle Prevent option, the dryer will go into standby.
Cycle Signal
Use this option to turn the signal indicating the end of
a drying cycle to low, medium, high, or off. The volume
you select here will also be applied to the Damp Dry
Signal.
NOTE: You may also turn off the tones that sound when
a feature, setting, or option is touched. Touch and hold
CYCLE SIGNAL for about three seconds to turn sounds
to low, medium, high, or off.
Damp Dry Signal
Touch to turn the Damp Dry Signal on or off. When
selected, a series of beeps will sound when the load
is damp, but not completely dry. This will allow you to
take clothes out of the load that do not need to dry
completely. This option is available on some cycles. The
Damp Dry signal is selected as a default for the Bulky
Items/Normal, Bulky Items/Wrinkle Control, and Bulky
Items/Heavy Duty cycles, as a reminder to manually
reposition bulky loads midway through the cycle.
Control Lock
Use this option to lock the controls of the dryer
and avoid an accidental change in cycle options or
preferences during a drying cycle.
Touch and hold CONTROL LOCK for 3 seconds to lock
or unlock the controls of the dryer. During this time, the
LED Display will count down “3-2-1.” Once the controls
are locked, the LED Display will display “Loc.”
NOTE: The Control Lock function may be enabled when
recovering from a power failure. To unlock the control,
touch and hold DAMP CONTROL LOCK for at least
three seconds.
Eco Dry Option
The Eco Dry option will default on only for the Normal
cycle and is only available on that cycle. This option
allows you to increase your energy savings by using a
slightly lower heat level. The Eco Dry option will increase
drying times by approximately 40 minutes, which will be
reflected on the LED Display. If optimal time is desired,
touch ECO DRY to turn off this option.
Check Vent
The Check Vent indicator is a feature available for
Automatic cycles only. This indicator will show the status
of airflow through the dryer and the dryer vent system
for the dryer’s life. During the sensing phase at the
beginning of the cycle, the Check Vent light will come on
if a blocked vent or low airflow issue is detected. This light
will stay on for the entire cycle. Should the Check Vent
light illuminate, refer to the “Troubleshooting” section for
potential solutions to the issue.
The light will be cleared upon completion of the cycle,
touching Power, or opening the door. The Check Vent light
will continue to illuminate during the cycle unless the root
cause is resolved.
REMEMBER: The dryer will continue to operate even
while the indicator is lit, but poor airflow can impact dry
times and overall performance. For more information on
maintaining good airflow, see “Check Your Vent System
for Good Airflow.”
NOTE: If there are other error issues during a cycle, the
Clean Check Vent indicator will not light up. See the
“Troubleshooting” section.
End
This will indicate that the selected cycle has ended and
the load may be removed from the dryer. If
Wrinkle Prevent has been selected, the dryer may continue
to tumble the load, even if “End” is displayed.
Control Lock
This will illuminate once the controls are locked
CYCLE STATUS INDICATORS
The Cycle Status Indicators show the progress of a cycle.
Not all indicators are available on all models.
Sensing
The Sensing indicator will light periodically during Sensor
Cycles to indicate that the moisture sensor on the dryer is
operating. This indicator will not light during Timed Cycles
or options such as Wrinkle Prevent.
Wet
The load is still wet and/or the cycle just started.
Damp
This indicator shows that the load is partially dried and
items that you may wish to hang up or iron while still
damp may be removed.
Cool Down
The dryer has finished drying with heat and is now
tumbling the load without heat to cool it down.
OPTIONS
Use to select available options for your dryer. Not all cycles
and options are available on all models.
Wrinkle Prevent Option
If you will be unable to remove a load immediately,
touch WRINKLE PREVENT to add up to 150 minutes of
periodic tumbling to help reduce wrinkling.
5
LED DISPLAY
When you select a cycle, its default settings will light up
and the Estimated Time Remaining (for Automatic Cycles)
will vary depending on the cycle selection, or actual time
remaining for Timed Dry cycles (for Manual Cycles) will be
displayed.
6
Loading ...
Loading ...
Loading ...