Magnetic Stirrer
Operation instruction
Ⅰ．Brief introduction
Magnetic Stirrer is widely used in various large and medium-sized institutions,
environmental protection, scientific research, sanitation, epidemic prevention, petroleum,
metallurgy, chemical industry, medical and other units, the equipment performance is good,
no noise, no vibration, mixing effect is remarkable, it is the ideal tool for experimental and
laboratory personnel.
Ⅱ．Parameters(1)
Model
Voltage
Heating
power
Rotational
speed
r/min
The highest
temperature
of working
plate
The highest
temperature
of beaker
The
maximum
capacity
Heating
plate size
mm
SH-2A
110V/220V
180W
-
300℃
80℃
2000ml
120
×
120
SH-2B
-
100-2000
-
-
SH-2AB
180W
100-2000
300℃
80℃
SH-3A
500W
-
300℃
100℃
5000ml
175
×
175
SH-3B
-
100-2000
-
-
SH-3AB
500W
100-2000
300℃
100℃
SH-3ABE
500W
200-2000
300
℃
100
℃
SH-3ABEII
500W
200-2000
300
℃
100
℃
SH-4A
600W
-
300
℃
100
℃
5000ml
190×190
SH-4B
-
100-2000
-
-
SH-4AB
600W
100-2000
300℃
100℃
SH-4ABE
600W
200-2000
300
℃
100
℃
SH-4ABEII
600W
200-2000
300
℃
100
℃
Remarks: A means heating function; B means stirring function; E means liquid crystal display.
The voltage is based on the product label.
Ⅲ．Parameters(2)
Model
Voltage
Heating
power
Rotational
speed
r/min
The highest
temperature
The maximum
capacity
Heating
plate size
mm
SH-6B
110V/220V
-
100-2000
-
1000ml×4
300×250
SH-7B
-
100-2000
-
3000ml
×
4
400
×
300
Remarks: The voltage is based on the product label.
Ⅳ.Operating instruction (liquid crystal display)
PV means the temperature, when there is no external sensor, it means the furnace plate
temperature, when the external sensor is connected, it means the external sensor temperature.
SV represents the rotational speed, the set state represents the setting rotational speed,
and the non-set state represents the running rotational speed.
If external temperature sensor is not placed in the beaker on the heating plate,
temperature change can't be sensed within ten minutes after the machine powered on，
instrument controller close the heating and show “pot”
1. Place the machine on a horizontal table, and then connect one end of the power cord
to the power jack on the back of the machine base
2. Plug the other end of the power cord into a standard socket.
3. Pay attention to the power switch on the right side of the machine base. The line (-)
means open, and the circle (o) means close.
4. Put the machine in a stable position, put the beaker containing liquid medicine in the
center of the working plate, put the appropriate rotor in the beaker, and make it in the center
of the beaker, turn on the power,the upper part of meter will show the working plate
temperature (If an external sensor is connected, will show the external sensor
temperature), the lower part of meter will show "OFF". press the "HEAT"knob,
the machine starts to heat ,by rotating "HEAT" knob to adjust to the required
temperature,(When the knob is rotated, the setting temperature will be displayed
on the upper part of the meter, 2 seconds after finishing rotation, the temperature
of the working plate will be displayed on the upper part of the meter).
samely,press the "STIR "knob,the machine starts to stir, by rotating "STIR" knob
to adjust to the required rotational speed,
(
When the knob is rotated, the setting
rotational speed will be displayed on the lower part of the meter. 2 seconds after
finishing rotation, current rotational speed will be displayed on the lower part of
the meter).
5. If need to measure the temperature of the liquid in the beaker, connect the bracket,
insert the sensor lead plug into the back of the machine, and then insert the sensor into the
liquid. the temperature displayed on the meter at this time is the temperature of the liquid.
Ⅴ. Operating instruction (no displayer)
Put the machine in a stable position, put the beaker containing liquid medicine in the
center of the working plate, put the appropriate rotor in the beaker, and make it in the center
of the beaker, turn on the power，adjust the temperature by rotating the "HEAT" knob at
different angels , the "HEAT" indicator light is on when heating, and the heating power is
adjusted by the "HEAT" knob.adjust the stir speed by rotating the "STIR" knob at different
angels , the "STIR" indicator light is on when stirring, and the STIR speed is adjusted by
the “STIR” knob.the temperature of the liquid in the beaker can be measured by a
thermometer fixed with a bracket.
Ⅵ. Matters needing attention
1. It should be avoided using in a humid environment.
2. When in use, the liquid in the beaker should not be put too full to prevent overflow during
stirring
3. Do not touch the working plate during using to avoid scald.
Ⅶ.
Ⅷ Packing List
Serial Number
Category
Name
Unit
Quantity
Remarks
1
Instrument
Magnetic Stirrer
Piece
1
√
2
Document
Operating
instruction
Piece
1
√
3
Attachment
Stir bar
Piece
1
√
4
Attachment
Bracket
Piece
1
Optional
5
Attachment
Sensor
Piece
1
Optional
