Loading ...
Loading ...
Loading ...
i
Features
Cycle Signal Control (some models)
When the Cycle Signal Control isON, asignal will sound at the end of eachcycle and
during the PressSaver setting (some models), The volume is adjustable or] some
models,
Drum Light (some models)
A drum light will come on whenever the door isopened to illuminate the dryer drum
during loading and unloading. Closing the door turns off the light.
f
oooÜoooooo_oo ooooooooo_oo0
co o co co ooo _
°oo o o _ _ co o
/_i % ° -- °°%°
°o o o°
® %%%___o oo oo o .... oo_?
\
o,
o_
o_
o_
Jse the drying rack to dry items which should
not be tumbled.
Drying Rack (some models)
Usethe drying rack to dry items which should not be tumble dried.
1. Open the dryer door and remove the lint screen.
2. Insert drying rack into the dryer drum. Placethe front bar under the lip of the lint
screen opening.
3. Placeitems to be dried on top of rack. Weight should not exceed 10 Ibs. Leave
space between items, but do not let items hang over the sides or through the
grids. Do not tumble other items when using the drying rack.
4. Selecta timed dry setting best suited for items being dried. Useonly the Air Fluff
(no heat) temperature setting for itemscontaining plastic, foam rubber, rubber-
like materials, feathers or down.
5. When items are dry, remove the rack and replace the lint screen. If lint screen
isnot in place, tumbling itemscould enter the exhaust systemand cause damage
to the dryer.
Common Drying
Problems
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage,
Forsatisfactory drying results, follow these suggestions provided byThe Soapand Detergent Association.
Greasy, oily ,Fabric softener sheet,
stains
Lint
Pilling
(Fibers break off,
ball up and cling
to fabric,)
Shrinking
Wrinkling
SOLUTIONS
• Rub fabric softener stains with bar
soap Rinse and rewash,
PI EVE TIVE MEA. URF.3
• Add a few bath towels to small loads for proper
tumbling,
• Some "silkdike" fabrics should be air dried,
• Use proper dging temperature
• Place fabric softener sheet on top of load before
starting the dryer,
,Overloading.
• Overdrying causes static
electricity.
• Lint screen not clean when
cycle began.
• Lint is attached to "pills,"
• Reduce load size and _ewash using
liquid fabric softener in the final rinse
•Or, add a fabric softener sheet and
tumble at low heat for 5-10 minutes,
• Use lint brush or roller to remove lint,
• Do not overload d_yer,
• Use fabric soRener in washer or dryer to reduce
static electricity,
• Remove items when they are slightly damp to
avoid overdrying,
• Check that lint screen is clean and in place
• Pilling is normal with synthetic ,Use a lint brush or shaver to remove
and permanent press fabrics, pills,
This is due to abrasion from
normal wear
• Use fabric softener to lubricate fibers.
•When ironing, use spray starch or fabric finish on
collars and cuffs,
•Turn items inside out to reduce abrasion,
,Overdrying,
• Irreversible condition • Follow fabric care label directions.
• If shrinking is a concern, check load often
• Remove items while slightly damp
• Block knits into shape,
• Lay flat to complete drying,
,Overloading.
• Leaving items in d_yer after
cycle ends
• Reduce load size and tumble at low
heat for 5 10 minutes,
• Remove items immediately, Hang or
fold,
• Do not overload d_yer,
• Remove items as soon as cycle ends
11
Loading ...
Loading ...
Loading ...