Loading ...
Loading ...
Loading ...
4
4
LIMITED WARRANTY
This unit is guaranteed to the original retail purchaser against
defects in quality or workmanship for a period of one year
from the date of original purchase. If this unit fails because of
a manufacturing defect within 30 days of purchase, return
the unit, with your receipt, to the retailer. After 30 days, but
within the warranty period, if the unit was purchased within
the continental United States, return it, freight prepaid, to
Albatross Industry.INC for repair or replacement. If the unit
was purchased outside the continental United States, return
the unit to the place of purchase. This warranty does not
cover damage caused by misuse, abuse, overheating or
alteration. Repairs made by anyone other than Albatross
Industry.INC are not covered in this warranty. Albatross
Industry.INC will not be held liable for any losses due to
neglectful operation. All implied warranties, including the
warranties of merchantability and of fitness of purpose, if
applicable, are hereby limited in duration to the period of
one year from the date of original retail purchase. Some
states do not allow limitations on how long an implied
warranty lasts, so the above limitations may not apply to you.
Incidental or consequential damages arising from a breach of
either express or implied warranties are hereby disclaimed
and excluded. Some states do not allow the exclusion of
limitation of incidental or consequential damages,so this
limitation or exclusion may not apply to you. Upon the
expiration of this warranty all such liability will terminate. No
other warranties are expressed or implied.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. No informal
dispute settlement mechanisms are available. This limited
warranty is given in lieu of all other warranties.
Manufactured for:
Albatross Industry, Inc.
5818 Sycamore Glen Road, Greensboro, NC 27405
www.albatrossindustry.com
Fig 1 Fig 2 Fig 3
Slide Cover to Open
Care and Maintenance
Cleaning: CAUTION-Before cleaning the fan be sure to unplug
the power cord from the outlet. Clean the grille surface with
a clean damp cloth. Do not use harsh chemical or abrasive
cleaners. DO NOT IMMERSE THE FAN OR ANY WIRES IN
WATER. Replace front grille before fan use. Allow fan to dry
completely before use. Periodic grille cleaning with a vacuum will
prevent dust build up. The motor is sealed and does not require
any interior maintenance, cleaning or lubrication.
Maintenance: The Internal motor bearings are permanently
lubricated at the factory and do not require any additional
lubrication.
Repair: DO NOT OPERATE THE FAN WITHOUT THE GRILLE IN
PLACE. DO NOT USE THE FAN IF IT HAS MALFUNCTIONED OR
BECOME DAMAGED IN ANY WAY.
Storage: Keep original carton for storage of the fan. Coil and tie
the power cord to avoid damage during storage.
indicates an overload or short-circuit situation. If the fuse blows,
unplug the product from the outlet. Replace the fuse as per the
Note: Some models come with a plug where you can replace a
fuse. If your model has this, please read and follow the below
instructions to replace the fuse.
This product employs overload protection (fuse). A blown fuse
user servicing instructions (follow product marking for proper
fuse rating) and check the product. If the replacement fuse
blows, a short-circuit may be present and the product should
be discarded or returned to an authorized service facility for
examination and/or repair.
Fuse Replacement
1. Grasp plug and remove from the receptacle or other outlet
device. Do not unplug by pulling on cord.
2. Open fuse cover by sliding open fuse access cover on top of
attachment plug towards blades. See Fig. 2.
3. Remove fuse carefully. Use a small tool to pry the end of the
fuse from holder cavity. Be careful not to break glass window.
4. Replace fuse. WARNING: Risk of re. Replace fuse only with
identical 2.5 or 5.0 Amp, 125 Volt fuse (3.6mm x 10mm). Make
sure the fuse is properly seated within its cavity.
5. Close fuse cover by sliding it back to its original closed
position.