Home
Bookmarks
Home
Bosch
Bosch PPH616B21A/03 User Manual
Bosch PPH616B21A/03 Serie 6 Gas hob
User Manual
For PPH616B21A/03.
PDF File Manual
,
12 pages
,
Read Online
|
Download pdf file
USER INSTRUCTIONS
USER INSTRUCTIONS
USER INSTRUCTIONS
USER INSTRUCTIONS
USER INSTRUCTIONS
USER INSTRUCTIONS
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
MAINTENANCE INSTRUCTIONS
MAINTENANCE INSTRUCTIONS
This cooktop is for use with Natural Gas and Universal LPG
This cooktop is for use with Natural Gas and Universal LPG
This cooktop is for use with Natural Gas and Universal LPG
This cooktop is for use with Natural Gas and Universal LPG
Leave this instructions with the owner
Ú
Ú
Ú
Ú
Ú
Ú
[es] Instrucciones de uso y montaje
Safety considerations
Safety considerations
Safety considerations
2
For your safety
For your safety
2
What to do if you smell gas
What to do if you smell gas
2
Warnings
Warnings
2
Installation
Installation
3
Warnings
Warnings
2
Statutory requirements
Statutory requirements
3
Preparing to install
Preparing to install
3
Clearances
Clearances
4
Installation of cooktop into the kitchen bench
Installation of cooktop into the kitchen bench
4
Connection
Connection
5
Converting the cooktop from Nat. Gas to Universal LPG
Converting the cooktop from Nat. Gas to Universal LPG
6
Changing the nozzles of the burners on the cooktop
Changing the nozzles of the burners on the cooktop
6
Adjustment of the taps
Adjustment of the taps
6
Operating instructions
Operating instructions
7
Burner locations
Burner locations
7
Accessories
Accessories
7
Operation
Operation
8
Cooking pans
Cooking pans
9
Cleaning and maintenance
Cleaning and maintenance
9
Service
Service
10
Wiring diagram
Wiring diagram
11
Produktinfo
Produktinfo
Produktinfo
Produktinfo
Produktinfo
Produktinfo
Produktinfo
Additional information on products, accessories, replacement parts and services can be found at
www.bosch-home.com
www.bosch-eshop.com
Safety considerations
Safety considerations
Safety considerations
Safety considerations
Safety considerations
For your safety
For your safety
For your safety
For your safety
For your safety
Do not modify this appliance.
Do not use or store flammable materials near this appliance.
Do not spray aerosols in the vicinity of this appliance while it is in operation.
If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
Do not store articles on or against this appliance.
What to do if you smell gas
What to do if you smell gas
What to do if you smell gas
What to do if you smell gas
What to do if you smell gas
Do not try to light the appliance.
Do not touch any electrical switch; do not use any phone in your building.
Inmediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by an authorised person.
Warnings
Warnings
Warnings
Warnings
Warnings
Do not allow the flame to extend beyond the edge of the cooking utensil. This instruction is based on safety considerations.
Do not forget that the unit becomes hot when in use. Common sense is important. Just because the flame is out, does not mean parts cannot still be hot.
This appliance shall not be used for space heating. This instruction is based on safety considerations.
Be sure to disconnect the electrical supply before disassembly of the appliance.
Keep the appliance area clear and free from combustible materials, gasoline and other flammable vapours and liquids.
This appliance must be installed in a position with the proper level of ventilation. Do not obstruct the flow of combustion and ventilation air.
Cabinets installed above the gas cooktop must have a minimum clearance of 650 mm (24”).
The gas pressure regulator supplied with the appliance must be installed in line with the gas pipe. (N.G. only).
For pressure testing in excess of 3.5 kPa (1/2 psig) the appliance and its individual shutoff valve must be disconnected from the gas supply piping system.
Important. When using a very large pot, leave a gap of at least 50 mm (2”) to avoid damaging any parts in bench top wood, plastic or other non-heat resistant materials. Never leave oil or hot fat unattended.
The surfaces on heating and cooking appliances get hot when in use. Be careful.
Keep children away from the appliance.
Only use your appliance for the preparation of food and
never
This appliance leaves the factory set for the gas supply indicated on the data label.
Call the Service Centre
Do not tamper inside the appliance. If necessary, call your local
Service Centre.
Overheated fat or oil can easily catch fire. Never leave the appliance unattended when cooking food with fat or oil, e.g. chips.
Never pour water on burning fat or oil.
DANGER OF BURNS!
In the event of a fault, cut the gas and electricity supplies to the appliance. Call our
Service Centre
Do not use unstable or uneven-based receptacles on cooking plates or burners. They may accidentally tip over.
If a gas supply knob/valve jams, do not force it. Call your official Service Centre immediately for them to repair or replace it.
The illustrations used in this booklet are only intended as a guide.
Grids become very hot during use. When operating the appliance control knobs, take care not to make contact with the grids.
Do not use this appliance neither in marine craft nor in caravans.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance ...
Make sure you keep these instructions for use and assembly in a safe place, so that you can hand them on with the appliance if it ever changes owner.
Note: To avoid jeopardising the electrical safety of the appliance, it is forbidden to use high-pressure or steam jet cleaning devices.
SHOULD THE RELEVANT CONDITIONS NOT BE PROPERLY SATISFIED, THE INSTALLER, AND NOT THE MANUFACTURER, SHALL BE HELD LIABLE.
SHOULD THE RELEVANT CONDITIONS NOT BE PROPERLY SATISFIED, THE INSTALLER, AND NOT THE MANUFACTURER, SHALL BE HELD LIABLE.
Installation
Installation
Installation
Installation
Installation
Statutory requirements
Statutory requirements
Statutory requirements
Statutory requirements
Statutory requirements
This installation must conform with the following:
This installation must conform with the following:
■ Manufacturer’s Installation instructions
■ Manufacturer’s Installation instructions
■ Local Gas Fitting Regulations
■ Local Gas Fitting Regulations
■ Municipal Building Codes
■ Municipal Building Codes
■ Refer to AS/NZS 5601.1 for Gas Installations
■ Refer to AS/NZS 5601.1 for Gas Installations
■ S.A.A. Wiring Code
■ S.A.A. Wiring Code
■ Local Electrical Regulations
■ Local Electrical Regulations
■ Any other statutory regulations
■ Any other statutory regulations
Preparing to install
Preparing to install
Preparing to install
Preparing to install
Preparing to install
Refer to AS/NZS 5601.1 for piping size details. These built-in cooktops are intended to be inserted in a benchtop cutout.
Only an officially authorised technician should connect the appliance.
Before you begin, turn off the gas and electricity supply.
Before connecting the unit, check whether the local connection conditions (type of gas) are compatible with the unit’s setting. Observe any special conditions imposed by local suppliers (utilities). The specifications of this cooktop are stated on ...
A duplicate data label is supplied for adhesion to an accessible location near the hotplate if the data label on the base of the hotplate cannot be accessed when the hotplate is installed.
Clearances
Clearances
Clearances
Clearances
Clearances
A range hood fitted above the top must be installed according to the installation instructions for the range hood. A minimum distance of 650 mm is required for a range hood and 750 mm for an exhaust fan.
Any adjoining wall surface situated within 200 mm from the edge of any hob burner must be a suitable non-combustible material for a height of 150 mm for the entire length of the hob. Any combustible construction above the hotplate must be at least 65...
A minimum depth of 50 mm from the top of the worktop surface must be provided for the appliance.
If the base of the hotplate can be touched, a protecting shield must be fitted.
■ The shield must be at least 10 mm from the lowest part of the hotplate and must be capable of withstanding the appliance temperatures. Minimum thickness of benchtop is 30 mm.
■ The shield must be at least 10 mm from the lowest part of the hotplate and must be capable of withstanding the appliance temperatures. Minimum thickness of benchtop is 30 mm.
■ The shield must be at least 10 mm from the lowest part of the hotplate and must be capable of withstanding the appliance temperatures. Minimum thickness of benchtop is 30 mm.
■ The shield material must be mdf or similar with minimum thickness of 12 mm.
■ The shield material must be mdf or similar with minimum thickness of 12 mm.
■ The shield overall dimensions must be 560 mm wide x 480 mm deep.
■ The shield overall dimensions must be 560 mm wide x 480 mm deep.
■ Provide cut-out in right hand rear of shield of 80 mm wide x 80 mm deep to provide for gas regulator / LP connection fitting.
■ Provide cut-out in right hand rear of shield of 80 mm wide x 80 mm deep to provide for gas regulator / LP connection fitting.
After installation of the shield the clearance around the top and sides of shield will allow adequate ventilation. Ensure the side and top clearances are not obstructed.
If an oven is positioned below the cooktop the barrier does not need to be fitted, but a space of 35 mm must be maintained between the underside of the cooktop and the top of the oven.
Installation of cooktop into the kitchen bench
Installation of cooktop into the kitchen bench
Installation of cooktop into the kitchen bench
Installation of cooktop into the kitchen bench
Installation of cooktop into the kitchen bench
Side clearances: If the distance measured from the periphery of the nearest burner to any vertical surface is less than 200 mm, the surface shall be protected in accordance with clauses 6.10.1.2 of AS/NZS 5601.1.
Make an appropriate size cut in the worktop surface, depending on the installation method: standard (a) or flush (b). For flush installation:
■ All cuts in the worktop surface should be done by a specialised shop.
■ All cuts in the worktop surface should be done by a specialised shop.
■ All cuts in the worktop surface should be done by a specialised shop.
■ The cuts should be clean and precise, as the cut edge is on the surface. The stability of the furniture should also be ensured after cutting work.
■ The cuts should be clean and precise, as the cut edge is on the surface. The stability of the furniture should also be ensured after cutting work.
■ Use only specially designed work surfaces, resistant to high- temperature and water (e.g. natural stone or tiled).
■ Use only specially designed work surfaces, resistant to high- temperature and water (e.g. natural stone or tiled).
■ Surrounding furniture must be resistant to temperatures up to 90 °C.
■ Surrounding furniture must be resistant to temperatures up to 90 °C.
Installation procedure:
a) Standard installation
a) Standard installation
a) Standard installation
Fitting the appliance onto the kitchen unit:
1. Remove the clips from the accessory bag and screw them into the position indicated so that they can turn freely.
1. Remove the clips from the accessory bag and screw them into the position indicated so that they can turn freely.
1. Remove the clips from the accessory bag and screw them into the position indicated so that they can turn freely.
2. Insert and centre the hob.
2. Insert and centre the hob.
Press the sides of the hob until it is supported around its entire perimeter.
3. Turn the clips and tighten them fully.
3. Turn the clips and tighten them fully.
The position of the clips depends on how thick the work surface is.
b) Flush installation
b) Flush installation
1. Complete a normal installation of the appliance making sure that it is surrounded by a uniform slot. The hob surface should be slightly below the work surface.
1. Complete a normal installation of the appliance making sure that it is surrounded by a uniform slot. The hob surface should be slightly below the work surface.
For tile worktops, if necessary, raise the bearing surfaces with strips resistant to water and temperatures.
2. Check the operation and position of appliance.
2. Check the operation and position of appliance.
3. Fill the gap between the worktop and hob with conventional silicone adhesive appropriate in the colour you desire.
3. Fill the gap between the worktop and hob with conventional silicone adhesive appropriate in the colour you desire.
Note: If unsuitable silicone adhesive is used on natural stone surfaces then this can produce colours that can not be removed. Our Technical Assistance Service can provide you with the most suitable glue (code 310818). Please note the manufacturers inst
Note:
4. Smooth the silicone adhesive with a scraper or wet finger moistened with soap and water before it forms a layer.
4. Smooth the silicone adhesive with a scraper or wet finger moistened with soap and water before it forms a layer.
5. Allow the silicone adhesive to dry before using the appliance.
5. Allow the silicone adhesive to dry before using the appliance.
Connection
Connection
Connection
Connection
Connection
Electrical
Electrical
Electrical
Electrical
Electrical
An electrical 10 amp socket needs to be within 1 m of the hotplate to allow electrical connection. The socket must remain accessible after installation of the appliance.
Important notes:
Important notes:
■ This appliance is connected to the mains (240 VAC) by means of the connecting lead which must be fixed to the kitchen unit to prevent it from coming into contact with hot parts of the cooktop (or an oven installed underneath) and remain accessibl...
■ This appliance is connected to the mains (240 VAC) by means of the connecting lead which must be fixed to the kitchen unit to prevent it from coming into contact with hot parts of the cooktop (or an oven installed underneath) and remain accessibl...
When making this connection make sure that the lead cannot come into contact with hot parts of the cooktop.
■ This appliance must be earthed. When connecting the cooktop ensure that the earth wire is connected first and that all wires are connected to the correct terminals.
■ This appliance must be earthed. When connecting the cooktop ensure that the earth wire is connected first and that all wires are connected to the correct terminals.
Gas
Gas
Gas
Gas
Gas
During the planning stage, consider the position of supply connections.
The cooktop must be connected to the gas supply with upstream connection of an isolation valve in accordance with the respectively valid regulations. We recommend that the isolation valve be fitted prior to the cooktop to enable isolation of cooktop ...
To find out the factory set gas type, see bottom of cooktop next to gas connection.
Remove plastic cap from gas supply line prior to installation.
Fit regulator (N.G.) or a test point (Universal LPG) directly to the R 1/2’’ connection.
Direction of gas flow is indicated on the rear of the regulator.
Position of the inlet connection:
Use pipe compound or thread sealant, properly theaded pipes and careful assembly procedure so that there is no cross threading, etc., which might cause damage or leakage.
Make sure that all connections peformed are free of leakage. The manufacturer does not accept any liability for leakage on connections performed by the installer or if the L-tube is moved or twisted.
There are two ways to carry out the connection to the main gas line:
■ The hotplate can be connected with rigid pipe as specified in AS/NZS 5601.1
■ The hotplate can be connected with rigid pipe as specified in AS/NZS 5601.1
■ The hotplate can be connected with rigid pipe as specified in AS/NZS 5601.1
■ Flexible Hose: If installing with a hose assembly, it must comply with AS/NZS 1869, 10 mm ID, class B or D, no more than 1.2 m long and installed in accordance with AS/NZS 5601.1.
■ Flexible Hose: If installing with a hose assembly, it must comply with AS/NZS 1869, 10 mm ID, class B or D, no more than 1.2 m long and installed in accordance with AS/NZS 5601.1.
Ensure that the hose does not contact the hot surfaces of the hotplate, oven, dishwasher or any other appliance that may be installed underneath or next to the hotplate. The hose should not be subjected to abrasion, kinking or permanent deformation a...
The supply connection point shall be accessible with the appliance installed.
WARNING: Ensure that the hose assembly is restrained from accidental contact with the flue outlet of an underbench oven.
Before Leaving- Check all connections for gas leaks with soap and water. DO NOT use a naked flame for detecting leaks. Ignite all burners both individually and concurrently to ensure correct operation of gas valves, burners and ignition. Turn gas tap...
It should be expressly noted that we cannot accept any liability for direct or indirect damage caused by wrong connection, leakage or improper installation. When being repaired, the appliance must always be disconnected from the mains supply; if requ...
Converting the cooktop from Nat. Gas to Universal LPG
Converting the cooktop from Nat. Gas to Universal LPG
Converting the cooktop from Nat. Gas to Universal LPG
Converting the cooktop from Nat. Gas to Universal LPG
Converting the cooktop from Nat. Gas to Universal LPG
To change injectors
To change injectors
To change injectors
To change injectors
To change injectors
All work involved in installation, setting and adaptation to a different gas type must be carried out by authorised personnel from our Service Centre and must comply with current regulations and the conditions laid down by the local gas company.
Request change-over injectors from our customer service deparment (refer injector chart below for sizes).
Natural Gas
Natural Gas
Universal LPG
Universal LPG
Burner
Burner
Hourly Gas Consumption (MJ)
Hourly Gas Consumption (MJ)
Injector mark
Injector mark
Hourly Gas Consumption (MJ)
Hourly Gas Consumption (MJ)
Injector mark
Injector mark
Auxiliary
Auxiliary
3,60
3,60
90
90
3,50
3,50
50
50
Semi-rapid
Semi-rapid
6,50
6,50
120
120
6,00
6,00
67
67
Rapid
Rapid
10,80
10,80
155
155
10,00
10,00
85
85
Double flame
Double flame
12,00
12,00
160
160
11,00
11,00
91
91
Triple flame
Triple flame
16,00
16,00
182
182
13,50
13,50
100
100
Before conversion the cooktop must be disconnected from the electricity and gas valves must be turned to the OFF position.
Changing the nozzles of the burners on the cooktop
Changing the nozzles of the burners on the cooktop
Changing the nozzles of the burners on the cooktop
Changing the nozzles of the burners on the cooktop
Changing the nozzles of the burners on the cooktop
1. Remove the pan supports, burner covers and diffusers.
1. Remove the pan supports, burner covers and diffusers.
1. Remove the pan supports, burner covers and diffusers.
2. Change the nozzles using the spanner provided by our Service Centre (code 340847, for double and triple flame burners code 340808), taking special care to ensure that the nozzle does not fall when it is removed from the burner or when fitted.
2. Change the nozzles using the spanner provided by our Service Centre (code 340847, for double and triple flame burners code 340808), taking special care to ensure that the nozzle does not fall when it is removed from the burner or when fitted.
Ensure that it is completely tightened in order to guarantee the seal.
Adjustment of the taps
Adjustment of the taps
Adjustment of the taps
Adjustment of the taps
Adjustment of the taps
1. Set the control knobs to minimum.
1. Set the control knobs to minimum.
1. Set the control knobs to minimum.
1. Set the control knobs to minimum.
1. Set the control knobs to minimum.
1. Set the control knobs to minimum.
2. Remove the control knobs from the taps. It has a flexible rubber valve reinforcing ring. Press with the tip of the screwdriver to access the tap's adjusting screw.
2. Remove the control knobs from the taps. It has a flexible rubber valve reinforcing ring. Press with the tip of the screwdriver to access the tap's adjusting screw.
2. Remove the control knobs from the taps. It has a flexible rubber valve reinforcing ring. Press with the tip of the screwdriver to access the tap's adjusting screw.
2. Remove the control knobs from the taps. It has a flexible rubber valve reinforcing ring. Press with the tip of the screwdriver to access the tap's adjusting screw.
Never remove the valve reinforcing ring. The valve reinforcing rings guarantee the watertightness of the appliance's interior from liquids and dirt, which might otherwise prevent its correct operation.
Never remove the valve reinforcing ring.
3. Adjust the minimum ring setting by turning the by-pass screw using a flat head screwdriver.
3. Adjust the minimum ring setting by turning the by-pass screw using a flat head screwdriver.
3. Adjust the minimum ring setting by turning the by-pass screw using a flat head screwdriver.
3. Adjust the minimum ring setting by turning the by-pass screw using a flat head screwdriver.
To adjust the minimum flame for N.G. replace the control knob onto the spindle, light the gas and turn the control knob to the small flame position. Screw the adjustment screw anti- clockwise to estabilish a minimum stable flame position. The flame s...
To adjust the minimum flame for N.G. replace the control knob onto the spindle, light the gas and turn the control knob to the small flame position. Screw the adjustment screw anti- clockwise to estabilish a minimum stable flame position. The flame s...
To adjust the minimum flame for N.G. replace the control knob onto the spindle, light the gas and turn the control knob to the small flame position. Screw the adjustment screw anti- clockwise to estabilish a minimum stable flame position. The flame s...
If the by-pass screw cannot be accessed, disassemble the grease drip tray, which is fitted to the hob with a series of screws. The following steps must be taken to remove it:
1. Remove all pan supports, burner caps, diffusers and control knobs.
1. Remove all pan supports, burner caps, diffusers and control knobs.
1. Remove all pan supports, burner caps, diffusers and control knobs.
2. Remove the screws from the burners.
2. Remove the screws from the burners.
3. To reinstall the appliance, proceed in the reverse order to disassembly.
3. To reinstall the appliance, proceed in the reverse order to disassembly.
Never remove the tap spindle. In the event of a malfunction, change the whole tap.
Important: After finishing, stick the sticker, indicating the new gas type, close to the specifications plate.
Important:
Operating instructions
Operating instructions
Operating instructions
Operating instructions
Operating instructions
Burner locations
Burner locations
Burner locations
Burner locations
Burner locations
"
!
"
"
"
#
#
#
1
$
$
Semi-rapid burner (up to
1.75
%
%
Rapid burner (up to
3
& Double-flame wok burner (up to 3.3 kW)
&
'
'
Triple-flame wok burner (up to
4
Accessories
Accessories
Accessories
Accessories
Accessories
The following accessories can be purchased from the Technical Assistance Service:
Additional wok pan support
Additional wok pan support
Additional wok pan support
Additional wok pan support
Only for use on wok burners with pans with a round base.
Only for use on wok burners with pans with a round base.
The additional wok pan support should be used to prolong the appliance's useful life.
The additional wok pan support should be used to prolong the appliance's useful life.
Additional coffee maker support
Additional coffee maker support
Additional coffee maker support
Additional coffee maker support
Only for use on the auxiliary burner with pans which are no more than 12 cm in diameter.
Only for use on the auxiliary burner with pans which are no more than 12 cm in diameter.
Simmer Plate
Simmer Plate
Simmer Plate
Simmer Plate
This accessory has been designed to reduce the level of heat at the lowest power setting.
This accessory has been designed to reduce the level of heat at the lowest power setting.
Place the accessory directly on the pan support with the cones facing upwards, never directly over the burner. Centre the pan over the accessory.
Place the accessory directly on the pan support with the cones facing upwards, never directly over the burner. Centre the pan over the accessory.
Simmer Cap
Simmer Cap
Simmer Cap
Simmer Cap
Lid specially designed to cook at minimum power. For its use, the Simmer Cap needs to be placed on the auxiliary burner cap.
Lid specially designed to cook at minimum power. For its use, the Simmer Cap needs to be placed on the auxiliary burner cap.
Code
Code
Code
Code
Code
Code
HEZ298126
HEZ298126
Additional wok pan support: cast iron (3.3 kW)
Additional wok pan support: cast iron (3.3 kW)
Additional wok pan support: cast iron (3.3 kW)
HEZ298127
HEZ298127
Additional wok pan support: cast iron (4 kW)
Additional wok pan support: cast iron (4 kW)
Additional wok pan support: cast iron (4 kW)
HEZ298110
HEZ298110
Additional wok pan support: steel enamel (3.3- 4 kW)
Additional wok pan support: steel enamel (3.3- 4 kW)
Additional wok pan support: steel enamel (3.3- 4 kW)
HEZ298114
HEZ298114
Additional coffee maker support
Additional coffee maker support
Additional coffee maker support
HEZ298105
HEZ298105
Simmer Plate
Simmer Plate
Simmer Plate
HEZ298128
HEZ298128
Simmer Cap
Simmer Cap
Simmer Cap
The manufacturer accepts no liability if these accessories are not used or are used incorrectly.
The manufacturer accepts no liability if these accessories are not used or are used incorrectly.
The manufacturer accepts no liability if these accessories are not used or are used incorrectly.
Operation
Operation
Operation
Operation
Operation
There are indications to show which burner each control knob operates.
It is essential to ensure that all the burner parts and pan supports are correctly installed for the appliance to work correctly. Do not swap the burner caps around.
Switching on automatically
Switching on automatically
Switching on automatically
Switching on automatically
Switching on automatically
If your hob can be switched on automatically (ignition sparkers):
1. Press the chosen burner control knob and turn it anticlockwise to the maximum power setting.
1. Press the chosen burner control knob and turn it anticlockwise to the maximum power setting.
1. Press the chosen burner control knob and turn it anticlockwise to the maximum power setting.
While the control knob is still pressed down, sparks are produced on all burners. The flame ignites.
2. Release the control knob.
2. Release the control knob.
3. Turn the control knob to the required setting.
3. Turn the control knob to the required setting.
If it does not come on, turn the control knob to the off setting and repeat the steps above. This time, press and hold the control knob for longer (up to 10 seconds).
: Risk of deflagration
: Risk of deflagration
If after 15 seconds the flame does not ignite, switch off the burner and open a nearby window or door. Wait at least one minute before trying to switch the burner back on.
Safety system
Safety system
Safety system
Safety system
Safety system
Depending on the model, your hob may have a safety system (thermocouple) that prevents the flow of gas if the burners accidentally switch off.
To ensure that this device is active:
To ensure that this device is active:
To ensure that this device is active:
1. Switch on the burner as usual.
1. Switch on the burner as usual.
1. Switch on the burner as usual.
2. Without releasing the control knob, press and hold it down firmly for 4 seconds after lighting the flame.
2. Without releasing the control knob, press and hold it down firmly for 4 seconds after lighting the flame.
Switching off a burner
Switching off a burner
Switching off a burner
Switching off a burner
Switching off a burner
Turn the corresponding control knob clockwise to the 0 setting.
Power levels
Power levels
Power levels
Power levels
Power levels
The progressive control knobs can be used to control the power needed, from minimum to maximum power.
