Loading ...
Loading ...
3
TABLE OF CONTENTS
1. PREPARE INSTALLATION
NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the retailer.
Make sure that the following items are included:
- Hood
- Decorative flue assembly (lower and upper flues)
- Hood mounting bracket
- Lower flue mounting bracket
- Upper flue mounting bracket
- 2 Aluminum grease filters
- 6” Round adapter/damper
- Installation instructions
- Parts bag: 8 no. 8 x 5/16” mounting screws,
7 no. 8 x 1½” mounting screws,
7 drywall anchors, 2 washers
Parts sold separately:
- Ducts, elbows, wall and roof caps.
- Non-duct kit model RK56, mandatory for non-ducted installation.
NOTE: During installation, protect countertop and/or cooktop.
HR0205A
DECORATIVE
FLUE
LOWER FLUE
MOUNTING
BRACKET
HOOD
MOUNTING
BRACKET
UPPER FLUE
MOUNTING
BRACKET
6” ROUND
ADAPTER/DAMPER
2. SELECT INSTALLATION TYPE
2.1 NON-DUCTED INSTALLATION
The RK56 non-duct kit is required for a non-ducted installation.
2.2 DUCTED INSTALLATION
Plan where and how the ductwork will be installed.
A straight, short duct run will allow the hood to perform most efficiently. Long duct
runs, elbows and transitions will reduce the performance of the hood. Use as few
of them as possible. Larger ducting may be required for longer duct runs.
Install wall or roof cap. Connect 6” round metal ductwork to cap and work back
towards the hood location. Use 2” metal foil duct tape to seal the joints.
2.3 ALL INSTALLATIONS
The minimum hood distance above cooktop is 26” (30” over a gas range).
A maximum of 30” above cooktop is recommended for best capture of cooking
impurities.
Distances over 30” are at the installer and users discretion providing that ceiling
height and decorative flue length allow it.
6” ROUND
DUCT
ROOF CAP
6” ROUND
ELBOW
WALL
CAP
HOOD
DECORATIVE
FLUE
HH0252A
26” MINIMUM ABOVE
COOKING
SURFACE
(30” FOR GAS RANGE)
WARNING
!
When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.
1. P REPARE INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. SELECT INSTALLATION TYPE . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. WIRING INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4. I
NSTALL HOOD MOUNTING BRACKET . . . . . . . . . . . . . . . . . . . . 4
5. INSTALL UPPER FLUE MOUNTING BRACKET. . . . . . . . . . . . . . . . 5
6. REMOVE GREASE FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . 5
7. I NSTALL 6” ROUND ADAPTER/DAMPER. . . . . . . . . . . . . . . . . . . 5
8. INSTALL THE HOOD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
9. D
UCT CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
10. PREPARE THE DECORATIVE FLUE. . . . . . . . . . . . . . . . . . . . . . 7
11. INSTALL THE DECORATIVE FLUE. . . . . . . . . . . . . . . . . . . . . .7-8
12. R
EINSTALL GREASE FILTERS. . . . . . . . . . . . . . . . . . . . . . . . . 8
13. OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
14. CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
15. REPLACEMENT PART S . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
16. WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Loading ...
Loading ...
Loading ...