Loading ...
Loading ...
Loading ...
CLEANING
Hand-Washing
Wash containers, lids and blade assembly
in warm, soapy water. Use a dishwashing
utensil with handle to avoid direct contact
with the blades. Exercise care when handling
the blade assembly as the blades are sharp.
Thoroughly rinse and air-dry all parts.
STUCK-ON INGREDIENTS IN THE
POWER NUTRI JUG & CUP
For stuck-on ingredients, such as nut
butter, rinse the jug and blade assembly
under warm water.
Next, fill the jug or cup with warm water up
to liquid fill or halfway on the cup and add
1–2 small drops of washing-up liquid.
Screw on the blade assembly and press
MIX. Twist the Power Paddle anti-clockwise
continuously while cleaning.
Then, empty contents and rinse under
warm water and wipe with a dishwashing
utensil, if needed.
12 13ninjakitchen.co.ukninjakitchen.co.uk
CARE & MAINTENANCE
Dishwasher
Containers, lids and blade assembly
are dishwasher safe. Ensure the blade
assembly and lid are removed from the
container before placing in the dishwasher.
Motor Base
Unplug the unit before cleaning. Wipe
motor base with a clean, damp cloth. DO
NOT use abrasive cloths, pads or brushes
to clean the base.
STORAGE
For cord storage, wrap cord with hook-
and-loop fastener near the back of the
motor base. DO NOT wrap the cord around
the bottom of the base for storage.
DO NOT store blended or unblended
ingredients in the cup or jug with the blade
assembly attached. Use only the spout
lid when storing blended or unblended
ingredients in the containers.
DO NOT stack items on top of the containers.
Store any remaining attachments alongside
the unit or in a cabinet where they will not be
damaged or create a hazard.
RESETTING THE
MOTOR THERMOSTAT
This unit features a safety system that
prevents damage to the motor and drive
system should you inadvertently overload
it. If the unit is overloaded, the motor will
be temporarily disabled. Should this occur,
follow the reset procedure below.
1 Unplug the unit from the
electrical socket.
2 Allow the unit to cool for approximately
15 minutes.
3 Remove the blade assembly from the
container. Empty the container and
ensure no ingredients are jamming the
blade assembly.
IMPORTANT: Ensure that maximum
capacities are not exceeded. This is the
most typical cause of appliance overload.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments,
visit ninjakitchen.co.uk
NOTE: The Power Paddle in the Power
Nutri Jug is not removable.
NOTE: For best results, use a dishwasher
to remove stuck-on ingredients.
1 SMALL DROP OF WASHING-
UP LIQUID
FILL WATER HALFWAY
FILL WATER TO
240ml LIQUID FILL
1 OR 2 SMALL DROPS OF WASHING-
UP LIQUID
TROUBLESHOOTING GUIDE
WARNING: To reduce the risk of shock and unintended operation,
turn power o and unplug unit before troubleshooting.
Display reads “- -”.
• If vessel is properly installed and the display reads ‘- -’, ensure the interior of the base
area is clean of any debris.
Control panel does not illuminate.
• Make sure unit is plugged in. If the unit is powered on and no container is installed, the
unit will display ‘- -’. The available programs will illuminate after placing a container on
base and rotating it clockwise until it clicks into place.
Control panel doesn’t turn o.
• Remove container from base by rotating it anti-clockwise and lifting it up. The display
with flash ‘- -’. Unplug the power cord from the socket. If the unit remains plugged in,
the display will time out after 3 minutes of inactivity. Press any button to wake the unit.
Doesn’t mix well; ingredients get stuck.
• Using the Auto-iQ programs is the easiest way to achieve great results. The pulses and
pauses allow the ingredients to settle toward the blade assembly. If ingredients are
routinely getting stuck, adding some liquid will usually help.
• When filling the cup, start with fresh fruit or vegetables, then leafy greens or herbs.
Next add liquids or yogurt, then seeds, powders or nut butters. Finally, add ice or
frozen ingredients.
• If using the Power Nutri Jug, during the blending process twist the Power Paddle anti-
clockwise continuously to circulate ingredients.
Unit moves on worktop while blending.
• Ensure the suction cup feet are clean and dry. Place the motor base on a smooth, clean
and level surface. Do not place motor base on a rough or unlevel surface as the suction
cup feet will not adhere properly.
Unit is dicult to remove from worktop for storage.
• If the motor base is dicult to remove from the worktop or table, slide it across the
surface, then lift. Tilt the motor base to disengage the suction feet.
Lid or Hybrid Edge Blades Assembly is hard to install on the container.
• Set the container on a level surface. Carefully place the lid or blade assembly on the
top of the container and align the threads so the lid/blade assembly sits flat. Twist
clockwise until you have a tight seal.
Can’t remove the Power Paddle from the Power Nutri Jug Lid.
• The Power Paddle in the Power Nutri Jug Lid is not removable. For cleaning
instructions, refer to the Cleaning section.
Loading ...
Loading ...
Loading ...