Loading ...
Loading ...
Loading ...
5
EARTHING INSTRUCTIONS
This appliance must be earthed. In the event of an
electrical short circuit, earthing reduces the risk of
electric shock by providing an escape wire for the
electric current. This appliance is equipped with a
cord having a earthing wire with a earthing plug.
The plug must be plugged into an outlet that is
properly installed and earthed.
WARNING : Improper use of the earthing plug can
result in a risk of electric shock. Consult a qualified
electrician or serviceman if the earthing instructions
are not completely understood, or if doubt exists as
to whether the appliance is properly earthed.
If it is necessary to use an extension cord, use only a
3-wire extension cord that has a 3-blade earthing
plug, and a 3-slot receptacle that will accept the plug
on the appliance. The marked rating of the extension
cord should be equal to or greater than the electrical
rating of the appliance.
IMPORTANT
The wires in this mains lead fitted to this appliance
are colored in accordance with the following code.
Green-and-yellow : Earth
Blue : Neutral
Brown : Live
As the colors of the wires in the mains lead of this
appliance may not correspond with the colored
markings identifying the terminals in your plug,
proceed as follows : the wire which is colored green-
and-yellow must be connected to the terminal in the
plug which is marked with the letter ‘E’ or by the
earth symbol or green-and-yellow. The wire which is
colored blue must be connected to the terminal
which is marked with the letter ‘N’ or colored black.
The wire which is colored brown must be connected
to the terminal which is marked with the letter ‘L’ or
colored red.
WARNING : The appliance must be earthed.
INSTALLATION
1. Ventilation
For correct operation, the oven must have sufficient
airflow. Do not block air vents as this may cause
overheating. In a freestanding situation allow
adequate ventilation around the microwave from
any overhead, rear and side wall constructions. If
combining the microwave with a trim kit for a 'built-in'
situation, (where more than one side of the
appliance is closed in) the specification and
installation requirements are as per the trim kit
instruction manual. Note: Cabinet materials must
be suitable to withstand temperatures up to 90˚C.
2. Steady, flat location
This oven should be set on a steady, flat surface.
3. Leave space behind and side
All air vents should be kept a clearance.
If all vents are covered during operation, the oven
may overheat and, eventually, oven failure.
4. Away from radio and TV sets
Poor television reception and radio interference may
result if the oven is located close to a TV, Radio
antenna, feeder and so on. Position the oven as far
from them as possible.
5. Away from heating appliance and water taps
Keep the oven away from hot air, steam or Splash
when choosing a place to position it, or the
insulation might be adversely affected and
breakdowns occur.
6. Power supply
• Check your local power source. This oven requires
a current of approximately 6 amperes, 240V 50Hz.
• Power supply cord is about 0.8 meters long.
• The voltage used must be the same as specified
on this oven. Using a higher voltage may result in
a fire or other accident causing oven damage.
Using low voltage will cause slow cooking. We are
not responsible for damage resulting from use of
this oven with a voltage of ampere fuse other than
those specified.
• If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a
hazard.
7. Examine the oven after unpacking for any
damage such as:
A misaligned door, Broken door, A dent in cavity.
If any of the above are visible, DO NOT INSTALL,
and notify dealer immediately.
8. Do not operate the oven if it is colder than room
temperature.
(This may occur during delivery in cold weather.)
Allow the oven to become room temperature before
operating.
Loading ...
Loading ...
Loading ...