Loading ...
Loading ...
Loading ...
Makecertaintheaugeranddriveclutchleversare
inthedisengaged(released)position.
MovethrottlecontroluptoFASTposition.
Insertignitionkeyintoslot.Becertainitsnapsinto
place.Donotturnkey.
NOTE:Engine will not start unless ignition key is
inserted into ignition slot in carburetor cover.
ElectricStarter
Determine that your house wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
WARNING: The electric starter is equipped
with a grounded three-wire power cord and
plug and is designed to operate on 120 volt AC
household current. Itmust be used with a
properly grounded three-prong receptacle at all
times to avoid the possibility of electric shock.
Follow all instructions carefully for preparing to
operate the electric starter.
If your home wiring system is not a three-wire
grounded system, do not use this electric starter
under any conditions.
If your home electrical system is grounded, but
a three-hole receptacle is not available, one
should be installed by a licensed electrician before
using the electric starter.
If your home is equipped with a grounded three-
prong receptacle, proceed as follows:
Rotate choke knob to OFF position.
Push the primer three times, fully covering the vent.
Connect power cord to switch box on engine. Plug
the other end of power cord intoa three-hole,
grounded 120 volt AC receptacle.
Push starter button on top of the engine to crank
engine. As you crank the engine, move choke knob
to FULL choke position.
When engine starts, release starter button, and
move choke gradually to OFF. If engine falters,
move choke immediately to FULL and then
gradually to OFF.
When disconnecting the power cord, always unplug
from the three-prong receptacle first and then from
the snow thrower.
RecoilStarter
Rotate choke knob to FULL choke position (cold
engine start). If engine iswarm, place choke in OFF
position instead of FULL.
Push primer button two or three times. Ifengine is
warm, push primer button once only.
Grasp starter handle and pull rope out slowly, until
it pulls slightly harder. Let rope rewind slowly.
Pull starter handle rapidly. Do not allow handle to
snap back. Allow itto rewind slowly while holding
firmly. Repeat until engine starts.
To
StopEngine
Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
To prevent possible freeze-up of starter:
Electric Starter: Connect power cord to switch box
on engine, then to 120 volt AC receptacle. With the
engine running, push starter button and spin the
starter for several seconds. The unusual sound
made by spinning the starter will not harm engine
or starter. Disconnect the power cord from recepta-
cle first, and then from switch box.
Recoil Starter: With engine running, pull starter
rope with a rapid, continuous full arm stroke three
or four times. Pulling the starter rope will produce a
loud clattering sound, which is normal.
Move throttle control to "stop" or "off" position.
Remove ignition key. Do not turn key. Disconnect
the spark plug wire from the spark plug to prevent
accidental starting while equipment isunattended.
NOTE: Keep it in a safe place. Engine will not start
without ignition key.
Wipe all snow and moisture from the carburetor
cover in the area of the control levers. Also, move
control levers back and forth several times.
To
EngageWheelDrive
With the engine running near top speed, move the
shift lever intoone of the six FORWARD positions
or two REVERSE positions. Select a speed
appropriate for the snow conditions that exist.
NOTE: Use slower speeds in higher snow, and until
you are familiar with the operation of the snow thrower.
Squeeze the traction control against the right
handle and the snow thrower will move. Release it
and the drive motion will stop.
IMPORTANT: Never move the shift lever without first
releasing the traction control. Doing so will cause
premature wear on the drive system's friction wheel.
ToEngageAugers
To engage augers and start snow throwing,
squeeze the auger control against the left handle.
To disengage power to the augers, release both the
auger control and the traction control, if engaged.
The auger control can be locked so you can turn the
electric chute directional control without interruptingthe
snow throwing process.
OperatingTips
NOTE: Allow the engine to warm up for a few minutes.
The engine will not develop full power until it reaches
operating temperature.
Loading ...
Loading ...
Loading ...