Loading ...
Loading ...
Loading ...
PROBLEM
Engine Will Not Start
Using Recoil Starter
Engine Stalls or Stops
After Running
Engine Loses Power
Excessive Vibration
Mower Will Not Move
Loss Of Traction
(Self-Propelled Models)
Cutting Grass
Improperly
Poor Grass Discharge
Oil Leaking
TROUBLESHOOTING
PROBABLE CAUSE
1. Fuel tank empty•
2. Engine needs choking or priming•
3. Spark plug wire disconnected•
1. Blade control is released or is not being held securely
against handle•
2. Choke control in the "CHOKE" position.
3. Fuel tank empty.
4. Engine air pre-cleaner and or air cleaner dirty.
5. Spark plug defective or gap set improperly.
6. Water, debris or stale fuel in fuel system•
1. Engine air pre-cleaner or air cleaner dirty
2. Spark plug faulty.
3. Water, debris or stale fuel in fuel system.
CORRECTIVE ACTION
1. Fill fuel tank with fresh fuel.
2.Choke/Prime. Check Engine Manual for
Instructions•
3. Place spark plug wire onto spark plug.
1. Blade control should be held securely against
handle at all times during operation of mower.
2. Move choke control to "OFF" position.
3. Fill with fuel to proper level•
4. Clean free of all debris•
5. Service spark plug.
6. Drain and clean fuel system.
1. Clean or replace filters.
2. Service spark plug.
3. Drain and clean fuel system•
•Service mower blade•
Service and tighten loose parts.
Replace air lifts. Tighten to proper torque.
Replace belt.
Replace pulley•
1. Damaged, out of balance or bent mower blade• 1
2. Loose blade components. 2.
3. Loose or missing air lift (if equipped)• 3.
4. Lumpy or frayed belt 4.
5. Bent Idler pulley 5.
1. Damaged transmission 1. Contact authorized SNAPPER dealer.
2. Engine drive belt broken requires replacement 2. Replace engine drive belt.
3. Engine drive belt has jumped off of the pulley 3. Reinstall belt onto pulley. Check for damage.
4. Poly V belt is broken. 4. Replace Poly-V belt.
5. Poly V belt has jumped off of the pulley 5. Reinstall belt onto pulley. Check for damage.
6. Driven disc slipping 6. Clean or replace driven disc.
7. Broken or loose differential link bolt 7. Tighten or replace link bolt.
1. Cutting height too low or high.
2. Engine speed too slow.
3. Forward ground speed too fast.
4. Terraced cut, side to side.
5. Excessive deck pitch, front to rear.
1. Adjust cutting height.
2. Move engine speed control to "FAST" position.
3. Move ground speed control to a slower speed•
4. Adjust height of cut with height adjust levers•
5. Adjust height of cut with height adjust levers.
6. Cutting blade dull or damaged. 6. Sharpen cutting edges or replace blade•
1. Engine speed too slow. 1. Move engine speed control to "FAST" position•
2. Forward speed too fast. 2. Move ground speed control to a slower speed•
3. Grass is wet. 3. Mow when grass is dry.
4,
5.
6.
7. Blade installed improperly on deck.
1. Leaking engine case•
Excessively worn or damaged blade. 4.
Build up of grass clippings and debris under deck. 5.
Improper blade installed on deck. 6.
7.
Service mower blade.
Clean deck.
Install proper SNAPPER blade.
Install blade properly.
1. Contact authorized SNAPPER dealer.
2. Check and tighten drain plug.
3. Make sure dip stick or oil filler cap is securely
in place.
2O
Loading ...
Loading ...
Loading ...