Loading ...
Loading ...
Loading ...
13GB
*1 Not supplied
*2 Speaker impedance: 4 to 8 × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a wired
remote control (not supplied).
For details on using the wired remote control, see “Using
the wired remote control” (page 14).
*5 Depending on the type of car, use an adaptor (not
supplied) if the antenna (aerial) connector does not fit.
*6 Whether in use or not, route the microphone input cord
so it does not interfere with driving operations. Secure
the cord with a clamp, etc., if it is installed around your
feet.
*7 For details on installing the microphone, see “Installing
the microphone” (page 14).
*8 For more information on how to install the SiriusXM
Connect Vehicle Tuner, consult the installation guide
included with the tuner.
*9
*10
Use speakers with 50W RMS or higher power input
capacity. Using Sony XB series full range speakers is
recommended.
*11
When the amperage rating of the fuse used on your car
is 10 A, make the power connection to the battery
directly to avoid short circuits.
*12
When using the steering wheel remote control, use the
connection cable RC-SR1 as necessary.
*13
Use the USB extension cable or a commercially
available one.
*14
Use the adhesive tape or a commercially available
one.
To a common ground (earth) point
First connect the black ground (earth) lead then
connect the yellow and red power supply leads.
To the +12 V power terminal which is
energized at all times
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the +12 V power terminal which is
energized when the ignition switch is set to
the accessory position
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the power antenna (aerial) control lead or
the power supply lead of the antenna (aerial)
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
Note
It will take about 10 seconds to shut down the output of
REM OUT after the unit is turned off.
To a car’s illumination signal
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the parking brake switch lead
The mounting position of the parking brake
switch lead depends on your car.
Be sure to connect the parking brake lead (light
green) of the power supply leads to the
parking brake switch lead.
To the +12 V power terminal of the car’s rear
lamp lead (only when connecting the rear
view camera)
When connecting to the battery directly
When the amperage rating of the fuse used on your
car is 10 A, make the power connection to the
battery directly to avoid short circuits.
to a metal point of car
to the positive battery terminal
Notes
• Despite connecting to the power supply lead of the car,
the unit may not fully provide its performance due to
insufficient power. In this case, make the power
connection to the battery directly.
• All power wires connected to the positive battery post
should be fused within 450 mm (18 in) of the battery post,
and before they pass through any metal.
• Make sure that the car’s battery wires connected to the car
(ground (earth) to chassis)* are of a wire gauge at least
equal to that of the main power wire connected from the
battery to the head unit.
• During full-power operation, a current of more than 15 A
will run through the system. Therefore, make sure that the
wires to be connected to the +12 V and GND terminals of
this unit are at least 14-Gauge (AWG14) or have a sectional
area of more than 2 mm² (
3
/32 in).
When making the speaker parallel connection, use wires
with more than 12-Gauge (AWG12) or wire that have a
sectional area of more than 3.5 mm² (
5
/32 in).
If you have any questions or problems concerning
the connection, consult the dealer for details.
Making connections
Parking brake switch lead
Hand brake type Foot brake type
*
Less than 450 mm (18 in)
+12 V car battery
Fuse (15 A)
Loading ...
Loading ...
Loading ...