Loading ...
Loading ...
Loading ...
Self Help
Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher itself. The
following information may help you with a dishwasher problem without involving a repair professional.
Dishwasher
does not start
Dishwasher
beeping (end
of cycle sig-
nal)
Display does
not illuminate
or console
lights are not
on
Dishwasher
seems to run
a long time
Dishes are not
getting clean
enough
Dishes are not
getting dry
enough
1. Door may not be properly latched
2. Unit may not be turned on
3. Unit not reset or previous cycle not completed
4. Delay start engaged
5. Interruption of electrical power supply to dish-
washer or blown fuse
6. The door may have been closed without first
selecting a cycle
7. Water supply may not be turned on
1. Default factory settings alert the customer that
the cycle is complete by beeping (top controls
only). This feature can be deactivated if so
desired
1. A fuse may have been blown or circuit breaker
tripped
2. Door not closed or latched
Note: For models with controls on top of the
door, the display only illuminates when the door
is opened and controls are visible
1. Incoming water is not warm enough
2. Cycle time can vary due to soil and water con-
ditions
3. Rinse aid dispenser is empty
4. Dishwasher connected to cold water supply
Note: Refer to "Wash Cycle Information" section
(page 9) in this manual for typical cycle lengths
1. Spray arm movement obstructed
2. Spray arm nozzles clogged
3. Improper use of detergents
4. Filters could be clogged
5. Dishes are nested or loaded too close together
6. Selected wash cycle is not suitable for food soil
conditions
1. Rinse aid dispenser is empty
2. Improper loading of dishes
3. Selected cycle does not include drying
Note: Plastic or Teflon do not typically dry as well
as other items due to their inherent properties
1. Shut the door completely
2. Press the main power switch to turn unit on
3. To reset, refer to "Operating the Dishwasher"
(page 9) in this manual
4. To reset, refer to "Delay Start" section (page 10)
in this manual
5. Check circuit breaker
6. Select a cycle, press start and close the door
7. Check and turn on water supply
1. To adjust the volume or deactivate, refer to the
"Cycle Completion Signal" section (page 10) in
this manual.
1. Check the fuse or circuit breaker box and
replace the fuse or reset the breaker if necessary
2. Ensure door is properly latched and completely
closed
1. Before starting a cycle, run hot water faucet at
the sink closest to the dishwasher
2. Sensors in the dishwasher automatically
increase the cycle time to ensure a good wash
when heavy soil is detected
3. Add rinse aid (page 6)
4. Verify dishwasher is connected to hot water sup-
ply plumbing
1. Ensure that spray arm movement is not blocked
by hand rotating spray arms before starting cycle
2. Remove the spray arms and clean according to
the "Care and Maintenance" section (page 11) of
the manual
3. Increase or decrease detergent depending on
the water hardness (refer to Table 1)
4. Clean the filters according to the "Care and
Maintenance" section (page 11) of the manual
5. Rearrange load such that water spray can reach
all items in the dishwasher- see "Loading the Dish-
washer" section (page 7) of the manual
6. Refer to "Wash Cycle Information" section (page
9) of the manual
1. Add rinse aid - the use of rinse aid improves dry-
ing
2. Rearrange load to ensure items are not nesting
(see "Loading the Dishwasher" section on page 7
of the manual)
3. Rinse and Hold setting does not include drying
Note: Santitize option and Intensive Drying feature
also improve drying performance.
12
Loading ...
Loading ...
Loading ...