Loading ...
FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW
If within one year from the date of purchase, this Craftsman Table Saw fails due to a defect in material or
workmanship, Searswill repair it, free of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE
OR SERVICE CENTER THROUGHOUT THE UNITED STATES.
This warranty givesyou specific legal rights, and you may also have other rights which vary from state to
state.
SEARS, ROEBUCK AND CO., Sears Tower, BSC 41-3, Chicago, IL 60684
3
GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and labels
affixed to the tool. Learn its application and
limitations as well as the specific potential hazards 13.
peculiar to this tool.
2. GROUND ALL TOOLS
This tool is equipped with an approved 3-conductor
cord and a 3-prong grounding type plug to fit the 14.
proper grounding tvPe receptacle. The green conductor
in the cord is the grounding wire. Never connect the
green wire to a live terminal. 15.
3. KEEP GUARDS IN PLACE
in working order, and in proper adjustment and
alignment.
4. REMOVE ADJUSTING KEYS 16.
AND WRENCHES
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
17.
5. KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents, Floor
must not be slippery due to wax or sawdust.
18.
6. AVOID DANGEROUS ENVIRONMENT
Don't use power tools in damp or wet locations or
expose them to rain. Keep work area well lighted.
Provide adequate surrounding work space.
7. KEEP CHILDREN AWAY
All visitors should be kept a safe distance from work
area.
8. MAKE WORKSHOP KID-PROOF
-- with padlocks, master switches, or by removing
starter keys.
9. DON'T FORCE TOOL
It will do the job better and safer at the rate for which
it was designed.
10. USE RIGHT TOOL
Don't force tool or attachment to do a job it was not
designedfor.
11. WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties or jewelry
(rings, wrist watches) to get caught in moving parts.
Nonslip footwear is recommended. Wear protective 21.
hair covering to contain long hair. Roll long sleeves
protectors (plugs or muffs) during extended periods of
operation.
SECURE WORK
Use clamps or a vise to hold work when practical, It's
safer than using your hand, frees both hands to operate
tool.
DON'T OVERREACH
Keep proper footing and balance at all times,
MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and
changingaccessories.
DISCONNECT TOOLS
before servicing; when changing accessories such as
blades, bits, cutters, etc.
AVOI D ACCl DENTAL STARTING
Make sure switch is in "OFF" position before plugging
in.
USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended
accessories, Follow the instructions that accompany
the accessories. The use of improper accessories may
causehazards.
19. NEVER STAND ON TOOL
Serious injury could occur if the tool istipped or if the
cutting tool is accidentally contacted.
Do not store materials above or near the tool suchthat
it is necessary to stand on the tool to reach them,
20. CHECK DAMAGED PARTS
Before further use of the tool, aguard or other part that
is damaged should be carefullv checked to ensure that it
will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
conditions that may .affect its operation. A guard or
other part that is damaged should be properly repaired
or replaced.
DIRECTION OF FEED
above the elbow. Feed work into a blade or cutter against the direction
12. USE SAFETY GOGGLES (Head Protection) of rotation of the bladeor Cutter only.
Wear Safety goggles (must comply with ANSI Z87.1) 22. NEVER LEAVE TOOL RUNNING
at all times. Everyday eyeglasses only have impact UNATTENDED
resistant lenses,they are NOT safety glasses,Also, use Turn power off, Don't leave tool until it comes to a
face or dust mask if cutting operation is dusty, and ear complete stop.
Loading ...
Loading ...
Loading ...