Loading ...
Loading ...
INSTALLATION / OPERATION / MAINTENANCE
8. Plugmotorcordintoa3-wiregrounded ll5voltA.C, out-
let 60 Hz., protected by a 15 amp fuse.
Use this pump only on 115 volt circuit.
Pump is equipped with an approved 3-
Hazardous . "
vNoal_aa_°°us conductor cord and 3-prong, grounding-
- type plug. To reduce the risk of electric
shock, be certain that it is connected to a properly
grounded, groundm.g-tyl_" receptacle.
Where a 2-prong wail receptacle is encountered, it must be
replaced witb a properly grounded 3-prong receptacle in-
stalled in accordance with the National Electrical Code and
local codes and ordinances.
NOTICE: Pump depends on water being pumped for lubri-
cation. DO NOT RUN PUMP DRY!
9. Pump should prime within 30 seconds. If not, disconnect
motor and do the following:
a. Disconnect inlet hose at pump. Pour contents of an-
other mineral oil packet into inlet port.
b. Check washers in inlet hose and make sure inlet line is
airtight.
c. Make sure inlet and discharge line are free of kinks and
restrictions.
d. Make sure pump is less than 10' (3m) above and 25'
(7.6m) to one side of water source.
lO.On older pumps that do not prime within 30 seconds,
check step 9 above. If pump still fails to prime, do the fol-
lowing:
a. If impeller is worn, replace it.
b. If pump head is internally worn, replace it.
[_, CAUTION Risk of burns from motor case during
normal operation. Do not much motor when it is operat-
ing or when it is hot. Plug nlotor cord into 3-wire grounded
I 15 voh AC. outlet 60 Hz.
[ _.WARNING ]Risk of fire or exph)sk)n if used to pump
flammable liquids or if used in explosive atmo-
spheres. Pump is designed to pump water at temperatures
between 32°-77 ° F (00-25 ° C) only. Pump water only with
this pump!
MAINTENANCE INSTRUCTIONS
[_WARNING]Hazardous voltage. Can shock, burn, or
cause death. Unplug pump before servicing.
BRUSH REPLACEMENT
Replace brushes after 150-200 hours of motor operation.
Check brush condition if motor shows signs of running
slowly or erratically after pump has been in service for ape-
riod of time.
NOTICE: Brushes are spring loaded. Hold on to covers,
brushes, etc., so that nothing gets lost.
l.Unserew brush covers on sides of motor. Slide brush
springs and brushes out of motor.
2. Slide new brushes into motor. Brush must slide into
square-cut hole in motor; make sure that curve on brush
end matches curve of commutator (see Figure 1).
3. Replace brush covers. Do not overtighten.
NOTICE: When using the Pud-L-Scoop TM, inspect washer in /'_k_ \ \
garden hose fitting to be sure it is in good condition. Attach
Pud-L-Scoop TM to end of inlet line and place at lowest point
of area to be pumped. Be sure connections are air tight. Pud-
L-Scoop TM requires at least 1/8" (3.2mm) minimum water
depth to prime. 5931293
NOTICE: This unit is not designed for applications involving
salt water or brine! Use with salt water or brine vdll void
warranty.
OPERATION
NOTICE." Do not run pump dry. Pump depends on water
being pumped for lubrication. If pump does not prime in
less than 30 seconds, recheck installation and plumbing.
Pump water only with this pump.
Pttmp will deliver 285 gallons (1079L) per hour (4.75 gallons
(18L) per minute) when discharge is not restricted. As dis-
charge is shut off and discharge pressure increases, capacity
will drop off. Pump is UL listed up to 28' of head or 12 psi
(8.5M or 82 kPa) discharge pressure.
Motor will heat when operated continuously. Motor case
temperature may reach 180 ° to 190°F (82 ° to 88°C) during
normal continuous operation.
Match brush curve
TO armature curve
Brush
must enter
square hole.
Figure I - Brush Replacement
Loading ...
Loading ...
Loading ...