Loading ...
Loading ...
Loading ...
Rinsing with the Adjustable Nozzle
WARNING: Be extremely careful if you must
use the pressure washer from a ladder,
scaffolding or any other relatively unstable
Iocation, When you press the trigger, the recoil
from the initial spray could force you to fall, or if
you are too close to the cleaning surface, high
pressure could force you off a climbing
apparatus.,
- Hook up the water supply and start your pressure
washer (see TO START THE PRESSURE
WASHER on page 8).
° Pull adjustable nozzle backward to get high
pressure mode,, Wait for detergent to clear,,
Detergent witl not flow when in the high pressure
mode.,
When detergent has cleared you may want to
expand the spray pattern for a more gentle rinsing
action° Start at top of area to be rinsed, working
down with same action as for cleaning,,
_lk CAUTION: Test a small, hidden area of the
surface to be cleaned, Make sure there is no
damage caused by the high pressure spray.
How to Use the Turbo Nozzle
The turbo nozzle rotates the high pressure stream in a
rapid circular pattemo The high pressure spray is most
effective when the tip of the wand is held between 8 to
24 inches from the surface being cleaned,,
Always start the turbo nozzle at a distance, gradually
getting closer to the surface until you get the cleaning
force you wahl
CAUTION! The turbo nozzle produces an
extremely high pressure spray which is capable
of removing paint and cutting holes through
surfaces if held too close,, Always make sure the
surface you will clean will not be damaged by
the high pressure spray by testing in a hidden
area.
Note: You cannot apply detergent with the turbo
nozzleo
To attach turbo nozzle to spray gun:
o Remove any accessories attached to the nozzle
extension,,
° Attach turbo nozzle to nozzle extension.
Connect the nozzle extension to the spray gun by
aligning the locking tabs on the accessory adapter
with the grooves in the gun., Push nozzle inward
and twist to lock in place_
BEFORE STARTING THE PRESSURE
WASHER
To operate the engine you will need to do the following:
Add Engine Oil
Only use high quality detergent oil rated with API
service classification SF or SG_ Select the oil's SAE
viscosity grade according to your expected operating
temperature:
colder _=,=.=== 32°F =,.===_ warmer
-< m >-
5W30 SAE 3O
Although multi-viscosity oils (5W30, 10W30, etc.)
improve starting in cold weather, these multi-viscosity
oils will result in increased oil consumption when used
above 32°F. Check your engine oil level more
frequently to avoid possible damage from running low
on oil
° Place pressure washer on a level surface
o Clean area around oit fill and remove oil dipstick°
° Wipe dipstick clean,,
- Pour oil from enclosed bottle into the oil fill opening
until oil reaches full mark on the dipstick. Stop and
check the oil level periodically. Do not overfill.
° Install oil dipstick, hand tighten securely,.
Add Gasoline
• Use regular unleaded gasoline with the pressure
washer engine. Fuel tank capacity is 1 USo quarL
_hk DANGER: Never fill fuel tank indoors., Never fill
fuel tank when engine is running or hot_ Do not
smoke when filling fuel tank.
_ AUTION: Do not overfill the fuel tank. Always
leave room for expansion.
,_ CAUTION: Experience indicates that alcohol
blended fuels (called gasohol or using ethanol
or methanol) can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel system
of an engine while in storage.,
To add fuel to engine:
o Clean area around fuel cap, remove cap,
° Add regular unleaded gasoline, slowly, to the fuel
tank.
Important; Never mix oil with gasoline.
° Install fuel cap and wipe up any spilled gasoline.
7
Loading ...
Loading ...
Loading ...