RBT Wallmount
AlcoLimit
©
User Manual
AlcoLimit Breathalysers Pty. Ltd.
P.O. Box 1106,
MANLY, NSW, 1655
Ph: 1300 667 661
www.alcolimit.com.au
Version 1.0
pg-3
CONTENTS
Description Page
Parts of your breathalyser ................................................................ 4
Specications ...................................................................................... 5
Installation............................................................................................ 6
Basic operation ................................................................................... 7
Results Displayed and Interpretation ............................................. 8
Maintenance Guide and Replacing Sensor Module..................... 9-10
Recalibrating the Sensor Module .................................................... 11
Error Messages .................................................................................... 12
General Warnings................................................................................ 13
Warranty .............................................................................................. 14
Disclaimer ............................................................................................ 14-15
Service Record .................................................................................... 16
Version 1.0
RBT Wallmount
©
AlcoLimit
©
pg-4
IMPORTANT INFORMATION
If you do not follow the instructions for use your test results may be
inaccurate and your warranty may become void.
For most accurate results, it’s important to wait at least 20 minutes after smoking, eating or drink-
ing before testing. This is a universal principle for all breathalysers, not just yours. The reason being
is that if you have recently consumed alcohol, the residual alcohol in your mouth is very high and
can cause a false reading. Additionally, waiting 20 minutes allows the alcohol to be absorbed from
your stomach into your bloodstream, contributing to more accurate test results.
PARTS OF YOUR BREATHALYSER
START TEST
BUTTON (on side)
PASS
LCD Display
Breath inlet
Version 1.0
CAUTION
FAIL
Breath Inlet: This is where the user places the straw to blow into the machine.
The sampling time is 5 seconds.
Start Button: Located on the right side of the machine.
Press the RED button to start the count down.
LCD display: The instructions for use are displayed on the LCD.
RBT Wallmount
©
AlcoLimit
©
pg-4 pg-5
SPECIFICATIONS
Recommended Usage Professional
Sensor Type Replaceable Electrochemical Fuel Cell
Accuracy Conforms to Australian Standard AS3547
Range %BAC 0.000 - 0.250
Display LCD
Warm-up time 20 seconds - 2 minutes
Breath Sampling Time 5 seconds
Temperature Operation 0C - 40C
Storage 0C - 50C
Housing Metal casing
Weight 4kgs
Power Source AC 110~220, 50/60 HZ, 0.5A input
DC 12V, 1.5A output
Connects to power point
Dimensions 13cm x 64cm x 33cm
Warranty 12 Month Limited Warranty
Specications are subject to change for the purpose of product improvement.
For all after-sales service and enquiries please contact the manufacturer:
AlcoLimit Breathalysers Pty. Ltd.
P.O. Box 1106
Manly, N.S.W. 1655
Australia
Ph: 1300 667 661 or +612 9939 3077
Website: www.alcolimit.com.au
Email: [email protected]
Version 1.0
RBT Wallmount
©
AlcoLimit
©
pg-6
INSTALLATION
Version 1.0
Installation should be performed by a qualied tradesperson.
We recommend 2 people perform this installation for ease of aligning the unit.
To install the RBT Wallmount Breathalyser on a wall you will need:
1 x Drill (not included)
1 x Philips-head screwdriver (not included)
2 x Screws & Wall plugs to suit the wall you will attach the unit to (not included)
1 x RBT Wallmount Breathalyser (included)
1 x Power pack (included)
1. Have person 1 hold the unit while the other person marks the holes in the wall with a
pencil. (Simply fold the back panel out and put it against the wall, then stencil the holes
on the wall with a pencil).
2. Put the breathalyser down, drill holes and insert wall plugs or your preferred tting.
3. Fold out the back panel and insert the screws (or chosen tting) through the holes in the
back panel into the wall. Ensure it is secure.
4. The breathalyser is now attached and you should be able to pull the front panel outward
from the wall and access the inside for servicing.
5. To secure the breathalyser from tampering always lock the casing with the key provided
6. Plug in the power pack underneath and plug it into a power socket. You may feed it
through a wall or use conduit to secure it to the wall and run it to the power point.
7. Turn on the power point and the unit will power up ready for use.
Please phone AlcoLimit Customer Service on 1300 667 661 if you have any questions regarding
installation.
RBT Wallmount
©
AlcoLimit
©
pg-6 pg-7
BASIC OPERATION
Version 1.0
ON-SCREEN GUIDANCE
Below are the steps followed by the user of the RBT Wallmount and the on-screen guidance.
The following is displayed until the start button is pressed:
KNOW YOUR LIMIT. CHECK YOUR ALCOHOL LEVEL.
PUSH BUTTON AND TAKE A STRAW.
The device will then prepare for testing:
WARMING UP, PLEASE WAIT….
When it is ready for testing the following will appear:
BLOW STEADILY UNTIL TONE ENDS
“SAMPLING”
The user will then need to blow into the unit for 5 seconds until the following appears:
SAMPLING IS COMPLETED.
“ANALYSING”
If you stop blowing or you do not breathe strongly enough, “Flow Error” will be displayed on LCD.
The device does not sense a proper breath sample, please wait and try again and the machine will
automatically prepare for a retest.
This process will continue until you nally obtain a correct result.
If the %BAC result reaches the maximum limit on the RBT (over 0.250%BAC) the software will pre-
vent another test for approximately 4 minutes. This is a safety precaution to prevent people using
the device for drinking games.
RBT Wallmount
©
AlcoLimit
©
pg-8
IMPORTANT INFORMATION
This device is tested as a 0.05% BAC device (0.05%BAC is equal to 0.05grams of alcohol per 100ml of
blood).
ALCOLIMIT RBT Wallmount has a range of 0.000-0.250 %BAC.
PLEASE NOTE: Alcohol vapour on your breath will cause a higher reading. We recommend having a glass of
water prior to testing and waiting at least 20 minutes after your last drink for accurate results. Not waiting the
required 20 minutes will saturate the sensor unnecessarily and may cause sensor damage. This is not covered
under your warranty. Please always wait 20 minutes after consuming any alcohol to avoid this problem.
Version 1.0
RESULTS DISPLAYED & INTERPRETATION
When the measurement is complete, the blood alcohol concentration (eg. 0.052%BAC) will appear on
the LCD display.
A visual guide on the front panel will indicate whether or not a person is aected by alcohol. We do not
recommend drinking and driving or working with any amount of alcohol in a person’s system.
The message for each level is:
PASS = 0.000%BAC
Very little or no alcohol has been detected.
CAUTION = 0.001-0.049%BAC
A moderate amount of alcohol has been detected.
FAIL = 0.050%BAC upwards
A high level of alcohol has been detected.
PRECAUTIONS
1. During testing, any alcohol traces left in a person’s mouth will increase the value of the blood
alcohol concentration level. Remove these traces before testing. Wait 20 minutes after drinking
or consuming medications with alcohol before testing.
2. When a person exhales through the straw, some unintentional salivation may aect the built-in
equipment. However, please be aware that placing any other liquids or materials into the straw
may cause the sensor to malfunction.
3. Cigarette smoking may also increase the blood alcohol concentration value. Allow ten minutes
after smoking before testing.
SEE WARNINGS SECTION FOR FURTHER PRECAUTIONS
RBT Wallmount
©
AlcoLimit
©
pg-8 pg-9
MAINTENANCE GUIDE
The software product is easy to maintain, and its operating environment can be managed onsite without
the need for specialist service technicians.
In order to service the RBT at your premises you will need to complete an online training course to be-
come certied to service the device in accordance with
Australian Standard AS/NZS3547. Details are available at www.alcolimit.com.au/elearning.
REPLACING THE SENSOR MODULE
The AlcoLimit RBT is uniquely designed to allow customers to replace the fuel cell sensor themselves.
To ensure accuracy of the RBT unit and maintain its calibration the following maintenance needs to be
performed when the calibration reminder appears.
• “Calibrationrequiredshortly”willbedisplayedontheLCDscreen.
• Youhave5daystoperformthemaintenanceprocedure.
• After5daystheRBTbreathalyserwillactivateitslockoutfunctionandwillnotworkuntilthis
procedure is completed.
Before starting this procedure please ensure you have a new pre-calibrated sensor module on hand to
replace the used one with.
We also recommend you keep a log of the following information:
- Date of sensor change
- Number of uses
- Number of hours
- Serial number of sensor used
- Name/Initials of sta member
- Certication number of sta member
(located on the sta members ‘Statement of Attainment’)
Ensure your hands are clean and free from oil or grease prior to touching the circuit board.
You will need 1 phillips head screwdriver.
Version 1.0
RBT Wallmount
©
AlcoLimit
©
pg-10
1. Turn the power o. (Very Important!!)
2. Unlock the AlcoLimit RBT and open the unit
3. Locate the sensor module and remove the 4 screws as indicated above
4. Pull out the sensor board above in the direction of the arrow.
5. Unplug the connector (press the clip) and insert the new sensor board
6. Plug in connector (ensuring the correct orientation), push the sensor board
in its correct place and replace the 4 screws tightly.
7. Turn on the power and the AlcoLimit RBT will perform an accuracy check.
8. The replacement is complete.
If the front display remains blank (no power) the sensor is not connected
correctly. Disconnect and reconnect the white cable again, ensuring it is the
correct orientation
With each new sensor purchased or calibrated by AlcoLimit Breathalysers a
“Calibration Certicate” can be ordered for $22. If you require this for auditing
purposes please request at the time of purchase/calibration.
Be sure to le this in the correct place for record keeping purposes.
Version 1.0
RBT Wallmount
©
AlcoLimit
©
pg-10
pg-11
Version 1.0
RECALIBRATING THE SENSOR MODULE
Return the used sensor to AlcoLimit Breathalysers for recalibration. Each sensor can be recycled multiple
times before a new one needs to be purchased (subject to volume of use).
For recalibration, return your sensor to:
AlcoLimit Breathalysers Pty. Ltd.
Recalibrations Dept.
P.O. Box 1106,
Manly, NSW, 1655
The cost of recalibration is $82.50. If you require a ‘Calibration Certicate’, please add $22. Return freight
is included.
Please be sure to include an ‘RBT RECALIBRATION REQUEST FORM’.
A copy is included with your initial purchase or email [email protected] for a copy. A new form will
be returned to you with each recalibration.
Your sensor will be tested, recalibrated and returned to you within 2-3 working days. We recommend you
always have a spare sensor on hand to minimise machine downtime.
RBT Wallmount
©
AlcoLimit
©
pg-12
ERROR MESSAGES
1. Flow error
If you stop blowing or you do not breathe strongly enough, “Flow Error” will be displayed on the
LCD. Please wait and try again and the machine will return to the testing mode.
2. Sensor error
A. Check if the alcohol sensor is in the right place on the board.
B. If you still have the error message, replace the sensor.
3. The screen is blank after replacing the sensor.
A. The sensor is not connected correctly.
B. Check you have connected the white cable in the correct direction and it is clipped to the
connector.
TROUBLESHOOTING GUIDE
1. The machine is plugged in, but there is no power.
Make sure that the line attached to the power adapter is connected correctly to the power socket
on the bottom of the machine. Make sure the power point is turned on.
2. There is no audible alert or sound.
Call AlcoLimit Breathalysers during oce hours (9-5pm M-F) and they will guide you through a
quick sound test
3. You blow, but the machine does not respond.
Check if the display window shows an error eg: “Sensor error”. If so, refer to error messages above.
4. After testing, the machine does not go back to the waiting mode.
The machine displays the result %BAC for 10 seconds. In order to go back to the testing mode,
the alcohol blown into the machine must be eliminated completely.
The amount of alcohol increases the time required for this elimination to be competed,
but it normally does not exceed 4 minutes. If it takes more than four minutes, the sensor may be
malfunctioning. Replace the sensor and if the error continues contact AlcoLimit Breathalysers on
1300 667 661.
Please note that the software has an inbuilt function to prevent people using the device for ‘drinking
games’. If a level of 0.250%BAC or over is blown into the machine it will not allow any additional tests for
4 minutes.
FOR FURTHER ASSISTANCE PLEASE CALL 1300 667 661.
Version 1.0
RBT Wallmount
©
AlcoLimit
©
pg-12
pg-13
Version 1.0
GENERAL WARNINGS (Please read carefully)
• Closedroomswithpoorventilation,pollution,smokeorairconditioningmaydelaythetimefor
resetting between tests.
• Notwaitingatleast20minutesafteryourlastalcoholicdrinkwillcauseinaccuratereadings.
Have a glass of water or other non-alcoholic beverage to minimise alcohol vapour & residue in
your mouth as this can cause a higher reading.
• Retest2-3timestoobtainareliabletestresult.Wesuggestyouthenwaitafurther10-20minutes
and retest to check that your level has stabilised and not increased.
• Bloodalcoholconcentrationcancontinuetoriseforupto2hoursafterthecessationofdrinking.
If the reading is close to the limit it is advised to wait a further 10-20 minutes and retest to
determine whether your %BAC has stabilised.
• Itcantake10hoursormoretoreturntoazeroreadingafterahighbloodalcohollevelhasbeen
reached. A further test should be carried out later in the day or the following morning.
• IfyouaretakingALCOLIMITRBToverseasorusingitatadierentaltitudepleasebeawarethat
the calibration may be aected.
• Donotblowcigarettesmokeorliquidintothetester.
• Alcoholaectseachindividualdierentlydependinguponmanyfactors;typeofalcohol,muscle
mass, weight, full or empty stomach, immune system, gender, regularity of drinking.
• Thosewithdiabetesmayndtheycandrinklargevolumesofalcoholyetstillread0.00%BAC.
This does not mean your ability to drive is not impaired.
• DonotuseALCOLIMITRBTasatooltodrinkanddriveoroperatemachinery.Thereisnosafelevel
of alcohol consumption before driving or operating machinery.
STORAGE CONDITIONS
Keep free from dust, dirt, and small particles as they may clog the sensor.
Keep in a cool dry place.
Keep out of extreme temperatures.
Keep out of reach of children.
Keep away from electrical interference.
Do not drop, knock or shake.
RBT Wallmount
©
AlcoLimit
©
pg-14
Version 1.0
WARRANTY
Manufacturer warrants for one calendar year the product to be free from defects in workmanship or
materials (excluding calibration) in normal service from the date of purchase. Manufacturer’s obligation
under this warranty is limited to replacing or repairing the unit if returned along with proof of purchase.
This warranty is void if unit has been tampered with, misused, dropped, maliciously damaged or used for
any purpose other than that intended.
The cost to return the unit to the manufacturer’s service centre is at the expense of the consumer. The
consumer is welcome to drop the unit o at our service centre in person. The consumer must contact our
customer service centre prior to returning the unit to us to enable our technicians to diagnose the fault
over the phone.
Upon returning the unit to our service centre under warranty, should the unit be found not to be faulty,
the consumer is liable for the freight cost to return the item to them. Should the unit be found to be
faulty the freight cost to return the item to the consumer will be borne by the manufacturer.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major failure.
DISCLAIMER
ALCOLIMIT RBT is recommended as a screening device only. The reading you receive is not legally
binding in a court of law, ALCOLIMIT RBT is to be used only as a guide. The only true indication of your
%BAC is a blood test.
We do not recommend driving or operating machinery with any amount of alcohol in your system.
Heavy nes and penalties may apply and the presence of alcohol in your system may void your
insurance.
The manufacturer gives no warranty, express or implied, as to the ability of ALCOLIMIT RBT to determine
or detect intoxication or to accurately indicate your blood alcohol level.
MANUFACTURER’S DETAILS
For recalibration and technical support, please contact us at:
ALCOLIMIT BREATHALYSERS PTY. LTD.
P.O. BOX 1106,
MANLY, NSW, 1655
Ph: (02) 9939 3077
or 1300 667 661
Fax: (02) 9938 3367
Web: www.alcolimit.com.au
RBT Wallmount
©
AlcoLimit
©
pg-14 pg-15
Version 1.0
Disclaimer cont’d
The manufacturer assumes no responsibility in circumstances where a person who has used the device
and received an indication of the presence of alcohol in his/her exhaled breath is later found to be under
theinuenceofortheirjudgmenthasbeenimpairedbyalcohol;andwillundernocircumstancesbe
liable for any loss or damage in contract or tort (including negligence) or otherwise suered by any
person arising directly or indirectly from the use of ALCOLIMIT RBT.
The manufacturer, importer or distributor takes no responsibility whatsoever for the use of this product
for any reason. This product must not be used as a tool for determining whether a person is able to oper-
ate a vehicle or machinery. The intake of any alcohol will impair reexes and judgment to operate motor
vehicles and machinery.
For further information on ALCOLIMIT RBT and to view other models available, see our website:
www.alcolimit.com.au or call our Customer Service line on 1300 667 661.
RBT Wallmount
©
AlcoLimit
©
RBT Wallmount
©
AlcoLimit
©
pg-16
Version 1.0
RECALIBRATION SERVICE RECORD
Date of
Recalibration
Service Details Technician
For service records to be updated, please send your instructions with your
sensor each time it is recalibrated.
Alternatively, you may request a Calibration Certicate at a cost of $22 (recommended for workplaces).
