Loading ...
Loading ...
Loading ...
NOTE:
All images shown are for illustrative purposes only and may not be an exact
representation of the product model.
NOTE:
The buttons for operating the heater on the heater control panel and the remote
control are the same. The indicator light will illuminate the icon of the function that is selected.
NOTE:
The indicator light and LED screen on control panel will o after 60seconds when
you stop operation.
USING THE HEATER
8 8
9
9
11
11
12
12
13
13
14
14
10
10
L:
Low heating power mode
H:
High heating power mode
AUT:
Temperature adjust mode
FAN:
Fan only mode
TIMER:
Timer setting mode
OSC.:
Oscillation mode
:
POWER indicator light
9
12
10
13
11
14
ON/OFF button
Temperature adjust UP/DOWN
Oscillation button
Timer button
Mode button
NOTE:
The indicator light will illuminate the icon of the function that is selected. The fan
remains on during all heater modes.
Flame Eect ON/OFF button
Press the POWER switch (9) to the on position I. The switch’s red indicator light will
illuminate and OF appears on the screen.
Press the ON/OFF button (10) on. The fan mode will start, the FAN indicator light will
illuminate, FA appears on the screen.
Press the MODE button (12) repeatedly to select one of the following options:
You can only set the temperature in Temperature adjust mode. To set the temperature,
press the UP/DOWN buttons (13) to increase or decrease the temperature to your desired
level. The temperature range is from 59° F to 95° F. The fan and heater will turn on and o
to keep the room at the set level.
Press the FLAME EFFECT ON/OFF button (15) repeatedly to turn the ame eect on or o.
To turn the heater o, press the ON/OFF button (10), the fan will run for 30 seconds to 1
minute to cool the heater and then the screen will turn o. Press the POWER switch (9) to
the o position O.
Unplug the heater from the mains power supply when it is not in use.
To oscillate (swing) the heater through 60 degrees, press the OSCILLATING button (11). The
OSC. icon illuminates when this function is on.
To stop the swing while the appliance is oscillating, wait until the airow is in the desired
position and press the OSCILLATING button (11).
The timer can be set to turn the heater o in 1 to 12 hours. When the heater is running,
press the TIMER button (14) repeatedly to set the hours. The TIMER icon illuminates when
this function is on. To turn the timer o, press the TIMER button (14) repeatedly until 00
appears.
Do not cover the heater or the air outlets/inlets/vents at any time while it is turned on.
There is a risk of re if the heater is covered.
For safety reasons, this heater is equipped with a tip-over sensor. This sensor automatically
shuts down the heater if it is not in an upright position while in operation. To resume
normal operation, check the heater is cool enough to handle, turn it upright and turn it on
again.
The heater has a built-in overheating protection mechanism. The safety mechanism will
turn o the power if the heater overheats. Press the POWER switch (9) to turn the heater
o and pull the mains plug from the socket. Wait 10 minutes for the heater to cool down.
NOTE:
In Temperature adjust mode, the heater must be set to a temperature level that
is at least a few degrees higher than the room temperature for the heating function to be
activated. If the heater does not appear to be working, increase the temperature until the
heating function turns on.
NOTE:
When you are not changing the time or temperature settings, the current room
temperature will display.
NOTE:
The ame eect will turn on automatically when the heater power is turned on.
NOTE:
LO – Low heating power mode
HI – High heating power mode
77 – Temperature adjust mode – The heater will adjust the power level to maintain the set
temperature. The default temperature for this mode is 77° F.
1.
2.
3.
4.
8.
9.
10.
5.
6.
7.
07 08
Loading ...