Loading ...
Loading ...
Loading ...
4. INTRODUCTION
4.1 SCOPE
Ideal for building sites and agricultural applications where mains power is not available.
4.2 SPECIFICATION
The Draper Tools policy of continuous improvement determines the right to change
specification without notice.
Stock no. ...............................................64065 ....................................................................24580
Part no. ............................................... PWP52 ..................................................................PWP81
Engine............................................ 4.8HP 4 stroke ..................................................7HP 4 stroke
Suction aperture................................50mm(2") ..........................................................80mm(3")
Output aperture................................ 50mm(2") ..........................................................80mm(3")
Max. flow............................................ 500L/min ...........................................................1000L/min
Max head height................................... 25M .........................................................................30m
Max suction head height........................8M ............................................................................7M
Application ...................................... Clean water ......................................................Clean water
Weight (net.) ........................................ 26kg . .....................................................................28.5kg
4.3 HANDLING & STORAGE
CAUTION: Always use and store this water pump correctly, never use or store this pump on
it’s side as oil or fuel may leak and damage the pump or your property.
If the pump has been used always allow it to cool for at least 30 minutes before transporting
the pump and ensure that the pump has fully cooled before returning it to storage as a hot
engine and exhaust system could cause personal injury or ignite some materials.
To prevent fuel/oil spillage when transporting, the pump should be secured upright in it’s
normal operating position with the engine switch in the off position.
Take care not to drop or strike the pump when transporting. Never cover the pump when in
use.
Before storing the pump for a long period:-
1. Be sure that the storage area is free of excessive humidity and dust.
2. Drain the fuel, storage procedure below.
A. Unscrew the fuel tank cap, remove the filter screen and empty the fuel tank into an
approved petrol container using a commercially available hand siphon
(Draper Stock No.43650), re-install the filter screen and fuel tank cap.
B. Loosen the carburettor drain screw and drain the carburettor into a suitable container.
C. Remove the spark plug maintenance cover and remove the spark plug cap.
D. Turn the engine switch to the OFF position.
E. Pull the starter cord 3 or 4 times to empty the fuel pump of petrol, into a
suitable container.
F. Turn the engine switch to the OFF position and tighten the carburettor drain screw.
MAINTENANCE
• Never modify the pump in anyway.
• Always maintain the pump in good working order regularly serviced by an authorised
service agent.
• Only use replacement parts supplied by the manufacturer.
• Only use fresh, clean and good quality fuel in the engine.
• Never operate the pump without oil.
• Never refuel in close proximity to naked flames, sparks or other sources of ignition, e.g.
cigarettes.
• Allow the engine to cool before refuelling and avoid spillage while refuelling.
• Wipe up and correctly dispose of any fuel spillage immediately with a suitable medium.
• Move away from the refuelling areas before restarting the engine.
• Store fuel for short periods only. Store in a container specifically designed for
petrochemical applications away from heat and direct sun light.
• After each use clean the pump thoroughly.
• Regularly check external nuts and fixings to ensure vibration caused by normal use has
not begun to loosen them.
5. HEALTH & SAFETY INFORMATION
WARNING!:
DO NOT OPERATE THIS MACHINE IN ANY HAZARDOUS LOCATION
Such areas include when there is a risk of an explosion of petrol fumes, leaking gas or
explosive dust.
CAUTION:
ENGINE SPEED HAS BEEN FACTORY SET TO PROVIDE SAFE OPERATION
Tampering with the engine speed adjustment could result in overheating of attachments
and could cause a fire. Never attempt to "speed up" the engine to gain more performance
as this will result in the output being thrown out of their standard design parameters,
potentially endangering the user and causing irreversible damage to the water pump.
NOTE:
PROTECT YOUR WATER PUMP
This water pump is NOT WEATHERPROOF and should not be exposed to direct sunlight,
high ambient temperatures and damp, wet or high humidity conditions.
14. EXPLANATION OF SYMBOLS
14.1 EXPLANATION OF SYMBOLS
Warning!
Read the instruction manual
WEEE
Do not dispose of Waste Electrical
& Electronic Equipment in with
domestic rubbish
Do not use in the wet.
Caution!
Danger!
Highly flammable liquid
For outdoor use only.
Do not expose to rain.
Caution!
Risk of electric shock
Warning!
Wear ear defenders.
Engine and exhaust
become hot during use;
do not touch.
NOTES
5
24
7
22
Loading ...
Loading ...
Loading ...