Loading ...
Loading ...
Loading ...
A WARNING: Do not allow familiarity with your drill-
driver to make you careless. Remember that a
careless fraction of a second is sufficient to inflict
severe injury.
BATTERY PACK
(MODEL 315.114520)
The battery pack for your tool has been shipped In a low
charge condition to prevent possible prebiems. Therefore,
you should charge it until light on front of charger changes
from red to green.
Note: Batteries will not reach full charge the first time they
are charged. Allow several cycles (drilling followed by
recharging) for them to become fully charged.
CHARGING BATTERY PACK
(MODEL 315.114520)
See Figure 1.
• Charge battery pack only with the charger provided.
• Make sure power supply is normal household
voltage, 120 volts, 60 Hz, AC only.
• Connect charger to power supply.
• Place battery pack in charger aligning raised rib on
battery pack with groove in charger. See Figure 1.
• Press down on battery pack to be sure contacts on
battery pack engage properly with contacts in charger.
• Normally, the red LEE) on charger will come on. This
indicates charger is [nfast charging mode,
• Red LED should remain on for approximately 1 hour
then the green LED will come on. Green LED on
Indicates battery pack Is fully charged and charger is In
trickle charge mode. Note: Green LED will remain on
until batten/pack Is removed from charger or charger
Is disconnected from power supply.
• If both yellow and green LED come on, this Indicates a
deeply discharged or defective battery pack.
Allow battery pack to remain in charger for 15 to 30
minutes. When battery pack reaches nern'_l voltage
range, red LED should come on.
If red LED does not come on after 30 minutes, this
indicates a defective battery pack and should be
replaced.
• Alter normal usage, a minimum of 1 hour of charging
time is required to fully recharge battery pack.
• The battery packwill become slightly warm tothe
touch while charging. This is normal and does not
indicate a problem.
• Do not place charger and battery pack In an area of
extreme heat or cold. Itwill work best at normal room
temperature.
Note; Charger aho battery pack should be placed in a
location where the temperature is more than 50°F but
less than 100°F.
• When batteries become fully charged, unp[ug charger
from power supply and remove the battery pack.
LED FUNCTIONS OF CHARGER
LED WILL BE ON TO INDICATE STATUS OF
CHARGER AND BATTERY PACK: (MODEL
315.114520)
• Red LED on= Fastcharging mode.
• Green LED on= Fullychargedand [ntricklecharge
mode.
• Green LED on= When batterypack IsInsettedInto
charger,Indicateshot battery pack orthat battery pack
Isout ofor belownormal temperature range.
• Yellowand Green LEDson = Deeplydischargedor
defectivebattery pack.
• No LED on = Defective charger or battery pack.
_i, CAUTION: To preventdamage to battery pack,
remove battery packfrom charger Immediately if no
LED comas on.Return batterypack and charger to
your nesrestSears Service Centerfor checldngor
rep[ec]ng.A[so, Ifyou are removing battery pack from
chargerand no LEDs are on, returnbothbatterypack
and chargerto your nearestSears Service Center.
Do notInsertanother batterypack intocharger. A
damagedcharger may damage a battery pack.
IMPORTANT INFORMATION FOR RECHARGING
HOT BATTERY PACK
When using your drill-driver continuously, the pattedes in
your battery pack will become hot. You should let a hot
battery pack cool down for apprexlmately 30 minutes
before attempting to recharge. When the battery pack
becomes discharged and Is hot, this will cause the green
LED to come on instead of the red LED. Alter 30 minutes,
reinsert battery pack in charger, ff green LED continues to
remain on, return battery pack to your nearest Sears
Repair Center for checking or repleclng,
Note; This situation only occurs when continuous use of
your drill causes the batteries to become hot. It does not
occur under normal circumstances. Refer to "CHARGING
BAI-rERY PACK" for normal recharging of batteries. If
the charger does not charge your battery deck under
normal circumstances, return both the battery pack and
charger to your nearest Sears Repair Center for electrical
check.
IMPORTANT INFORMATION FOR RECHARGING
COOL BATTERY PACK
If battery pack Is below normal temperature range, the
green LED on charger will come on. Allow battery pack to
reach normal temperature, than the red LED will coma on.
Note', Refer to "CHARGING BATTERY PACK" for
normal recharging of batteries, If the charger does not
charge your battery pack under normal circumstances,
return both the battery pack and charger to your nearest
Sears Repair Center for electrical check.
10
Loading ...
Loading ...
Loading ...