Loading ...
Loading ...
Loading ...
CODE EXPLANATION
n. CE CLEAR ESCROW OPTION
When selected, money held in escrow for 30
minutes without further escrow or cycle activity
will be cleared.
CE Selected 'ON'. Press the COLD button once for
this selection.
--> Press the WARM button once to advance
to next code.
CODE EXPLANATION
U. 00 PENNY iNCREMENT OFFSET
U. 00 This represents the penny increment price offset
used in Generation 2 (Enhanced Debit) Card
Payment Systems. Choose from 0-4 pennies by
pressing the HOT button.
-> Press the WARM button once to advance
to next code.
A1. 00 PREWASH LENGTH
AI. 00 This is the number of minutes of PREWASH.
Choose 0 to disable the prewash or select
between 2 and 7 minutes by pressing the HOT
button.
-> Press the WARM button once to advance
to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Represents the number of cycles in HUNDREDS.1 02 = 200
2 00 Represents the number of cycles in ONES. 2 2`5 = 25
TOTAL = 225
cycles
This is "VIEW ONLY" and cannot be cleared.
Press the WARM button once to advance to next code.
If money counter (1.0C or 1.00) is selected, the following
is true:
3 00 Number of dollars in HUNDREDS.
4 00 Number of dollars in ONES.
5 00 Number of CENTS.
END OF SET-UP PROCEDURES
3 01 = $100.00
468= $ 68.00
5 7.5 = $ .75
TOTAL = $168.75
EXIT FROM SET-UP MODE
All Models: Reinstall access door.
if AA1 connector was removed to access Set-up Mode:
-->Unplug washer or disconnect power.
-->Open console, reinsert plug on AA1, close console.
-->Plug in washer or reconnect power.
CLEANINGYOURWASHER
Cleaning the Door Seal/Bellow
1=
2.
3.
Open the washer door and remove any clothing or items
from the washer.
Inspect inner glass door. If debris is present, wipe off debris
using damp cloth.
Inspect colored seal/bellow between the door opening and
the basket for stained areas. Pull back the seal/bellow to
inspect all areas under the seal/bellow and to check for
foreign objects.
IM PORTANT:
[] Wear rubber gloves when cleaning for prolonged periods.
[] Refer to the bleach manufacturer's instructions for proper use.
Washer Maintenance Procedure
This washer has a special cycle that uses higher water volumes
in combination with liquid chlorine bleach to thoroughly clean the
inside of the washer.
NOTES:
[]
[]
Read these instructions completely before beginning the
cleaning process.
If necessary, the cleaning cycle may be interrupted by
pressing the COLD button twice. However, this will not
immediately stop the cycle. The machine will continue with
several rinse and drain steps to ensure that all remaining
bleach is rinsed from the washer.
A. Seal/Bellow
4. If stained areas are found, wipe down these areas of the
seal/bellow, using the procedure that follows.
a} Mix a dilute solution, using 3/4 cup (177 mL) of liquid
chlorine bleach, and 1 gal. (3.8 L) of warm tap water.
b} Wipe the seal/bellow area with the dilute solution,
using a damp cloth.
c) Let stand 5 minutes.
d) Wipe down area thoroughly with a dry cloth and let the
washer interior air dry with door open.
Begin procedure
1. Open the washer door and remove any clothing or items
from the washer.
2,
Open the dispenser drawer and immediately add 2/3 cup
(160 mL) of liquid chlorine bleach to the bleach compartment.
NOTE: Do not add any detergent to this cycle. Use of more
than %cup (160 mL) of bleach will cause product damage
over time.
3=
4.
Close the washer door and the dispenser drawer.
To start the Washer Cleanout cycle, first enter "Start
Operating Set-up." Then press and hold COLD for one
second. With the entire display flashing, press COLORS/
DELICATES.
NOTE: The door will lock, the basket will rotate 1/2 turn,
then the door will unlock and lock again, then the Washer
Cleanout cycle will continue.
12
Loading ...
Loading ...
Loading ...