INSTALLATION GUIDE
US CA
I
NTEGRATED WB30SDEI
WARMING DRAWER
3
CONTENTS
Safety and warnings 5
Warming drawer models 6
Unpack your product 7
Electrical specifications 7
Parts supplied 8
Tools required 8
Product dimensions - 30" integrated models 9
Cabinetry dimensions - 30" integrated models 10
Front panel specifications 11
Installation options 11
Installing the drawer 14
Adjusting the depth 16
Adjusting the height 16
Installer checklist 17
5
SAFETY AND WARNINGS
!
WARNING!
Tip Hazard
This product may tip. Keep children away and
take care. Failure to follow this advice may
result in injury.
• Drawer must be secured in place by supplied
screws.
• Ensure there is a fixed shelf directly above
the drawer if it is not installed under another
product.
!
WARNING!
Cut Hazard
Failure to use caution could result in injury.
• Take care: some edges may be sharp.
• Do not put fingers in the drawer when closing.
!
WARNING!
Electric Shock Hazard
Failure to follow this advice may result in
electrical shock or death.
• If the product is damaged, switch the appliance
off and disconnect it from the mains to avoid
possible electric shock.
!
WARNING!
420-630 lb
190-285 kg
Weight Hazard
Failure to follow this advice may result in
damage or personal injury.
• Ensure the bottom shelf of the cabinetry can fully
support the weight of combined appliances.
6
SAFETY AND WARNINGS WARMING DRAWER MODELS
READ AND SAVE THIS GUIDE
WARNING!
To reduce the risk of fire, injury to persons or damage when using the appliance, follow the
important safety guides listed below. Read all the instructions before using the appliance.
Installation
z
Please make this information available to the person installing the product.
z
The appliance must be installed by a qualified installer, or Fisher & Paykel trained and
supported service technician to avoid faulty electrical connection.
z
Ensure the installation complies with all clearance requirements and applicable standards
and regulations.
z
When installed in combination with a companion product, the companion product can be
placed directly onto the appliance. A built-in shelf at the base of the cabinetry must be
able to support the weight of both products.
z
Ensure the cabinetry is square and level and with correct dimensions.
z
If installing the appliance directly underneath an oven, ensure you do not damage the
oven’s lower trim. Fisher & Paykel does not accept any responsibility for any damage
resulting from incorrect installation.
z
Before installing the appliance, inspect for any signs of damage. Do not install or use
damaged appliances.
z
Be careful when stacking the appliances on top of each other to avoid damage to the
appliances.
Electrical
z
All connections for electrical power and earthing must be done by a qualified electrician
and must comply with local codes and ordinances.
z
Before installation, ensure that the voltage and frequency listed on the data plate
corresponds with the household electrical supply.
z
When combining with another appliance, ensure each appliance has its own power outlet.
Avoid sharing the power point to prevent accidental switching off of the appliance.
z
Ensure your appliance is properly grounded (earthed).
z
Connect the drawer to a properly rated, protected and sized power supply circuit to avoid
electrical overload.
z
Do not use an extension cord or a portable electrical outlet device (e.g. multi-outlet outlet
box) to connect the drawer to the power supply. Ensure the power supply cord is located
so that it will not be stepped on, tripped over or otherwise subject to damage or stress.
z
Ensure there is a switched outlet in an easily accessible area within 35 7/16” (900mm) of
the centre rear of the product.
Servicing
z
Do not repair or replace any part of the appliance unless specifically recommended in the
user guide. All other servicing should be done by a Fisher & Paykel trained and supported
service technician or qualified person.
z
Always disconnect the power supply before doing any installation, maintenance or repair
work.
z
If the power supply cord is damaged, it must be replaced by a qualified electrician or
Fisher & Paykel trained and supported service technician.
30" Warming Drawer,
Integrated style
WB30SDEI
7
Remove the warming drawer and accessories box from the packaging. Recycle the materials
that can be reused. Dispose packaging materials in accordance with local regulations on waste
disposal.
Inspect the warming drawer for any signs of damage. Do not install the warming drawer if it
has been damaged. If the product is damaged, contact your local Fisher & Paykel dealer.
UNPACK YOUR PRODUCT ELECTRICAL SPECIFICATIONS
RECYCLE
RESPONSIBLY
All electrical work must be done by a qualified electrician, or a Fisher & Paykel trained and
supported service technician.
WB30SDEI
Supply 110 VAC, 60 Hz
Service 10 amp circuit
Maximum Power 810 W
Power outlet* 3-prong grounding-type
Power cord (total length) 70 7/8" (1800mm)
* The power outlet must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.
8
Wire shelf (1)
Bracket spacer (1)
Installation guide (1)Service & Warranty
(1)
SERVICE & WARRANTY
SERVICE ET GARANTIE
ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ
SERVIZIO E GARANZIA
SERVICE & GARANTIE
HUOLTO JA TAKUU
SERVICE OG GARANTI
保修和维修
服務和保修
INSTALLATION GUIDE
US CA
INTEGRATED W30SDEI
WARMING DRAWER
User guide (1)
USER GUIDE
US CA
WARMING DRAWER
MINIMAL WB24SDEB2 & WB30SDEB1
CONTEMPORARY WB24SDEX2 & WB30SDEX1
PROFESSIONAL WB30SPEX1
INTEGRATED WB30SDEI1
5mm Hex key T15 star-head
screwdriver
Leveler
PARTS SUPPLIED TOOLS REQUIRED
T15 star head
wood screw (12)
T15 star head
machine screw (6)
Side brackets (2) Bracket cover (5)
Ruler
9
PRODUCT DIMENSIONS - 30" INTEGRATED MODELS
g
D
f
PROFILE
h
PLAN
e
i
c
FRONT
a
b
ISOMETRIC
Actual product dimension may vary by ± 2 mm.
PRODUCT DIMENSIONS
WB30SDEI
IN MM
A Overall height 10 11/16 271
B Overall width 28 7/16 723
C Overall depth* 22 3/16 564
D Height of chassis 10 11/16 271
E Width of chassis 27 13/16 707
F Height of door frame 10 1/2 267
G Depth of door frame** 11/16 17
H Depth of open drawer 16 1/2 419
* Including power plug and drawer frame
** Measured from back of chassis flange to front of door frame.
PRODUCT WEIGHT
WB30SDEI
LBS KG
Total weight of drawer* 75 34
*including packaging
10
CABINETRY DIMENSIONS - 30" INTEGRATED MODELS
FLUSH INSTALL
c
b
d
PO*
a
PROFILE
PO*
e
f
CABINETRY DIMENSIONS
WB30SDEI
INCHES MM
A Minimum inside height of cavity 10 3/4 273
B Minimum inside width of cavity min 28 9/16 - max 28 3/4 min 725 - max 730
C Minimum inside depth of cavity 22 1/2 572
D Overall width of cabinetry 30 762
E Minimum clearance between top of door frame
and upper cabinetry panel
1/8 3
F Minimum clearance between bottom of door
frame and lower cabinetry panel
1/16 2
* The power outlet (PO) must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.
Actual product dimension may vary by ± 2 mm.
custom panel
11
FRONT PANEL SPECIFICATIONS
Ensure the back and sides of the panel and cabinetry around the drawer are completely sealed
with a waterproof vapour barrier (ie polyurethane) to prevent damage to the panel.
STANDALONE INSTALLATION
This installation is suitable for Minimal, Contemporary & Professional Warming drawers. A fixed
shelf must be installed above the warming drawer.
PROFILE
Top shelf
Bottom shelf
Warming Drawer
FRONT
INSTALLATION OPTIONS
FRONT PANEL DIMENSIONS
WB30SDEI
IN MM
A Height of drawer front panel 10 1/2 267
B Width of drawer front panel 29 15/16 760
C Depth of drawer front panel 13/16 16-20
a
c
b
FRONT PANEL WEIGHT
WB30SDEI
LBS KG
Total weight of drawer front panel 11 5
12
This combination is suitable for 24" and 30" Warming Drawers that can fully support
24" and 30" Fisher & Paykel wall ovens, respectively.
COMBINED WITH SINGLE OVEN
PROFILE
Single oven
Warming Drawer
FRONT
Bottom shelf
This combination is suitable for 24" and 30" Warming Drawers that can fully support
24" and 30" Fisher & Paykel companion products, respectively.
COMBINED WITH COMPANION PRODUCT
PROFILE
FRONT
Companion product
Warming Drawer
Top shelf
Bottom shelf
INSTALLATION OPTIONS
13
This combination is suitable for 30" Warming Drawers that can fully support a
30" Fisher & Paykel double oven.
COMBINED WITH DOUBLE OVEN
This combination is suitable for 30" Warming Drawers. A shelf is required above the oven to
support the 30" companion product. Ensure the bottom shelf can fully support the weight of
all appliances.
COMBINED WITH SINGLE OVEN & COMPANION PRODUCT
FRONT
PROFILE
Companion product
Top shelf
Wall oven
Bottom shelf
Warming Drawer
30” Companion Trim Kit
FRONT
PROFILE
Double oven
Warming Drawer
Bottom shelf
INSTALLATION OPTIONS
14
1
4
INSTALLING THE DRAWER
Use the supplied spacer to
locate the attachment position
of the cabinet brackets to
correct depth.
Secure the cabinet brackets to
the side panels of the cabinetry
with T15 wood screws (6x).
Check the base of the cabinetry
using a leveler or ruler.
Ensure the cabinetry is square
and base is level.
Secure the bracket cover and
chassis flange to the cabinet
brackets with T15 machine
screws (6x).
cabinet bracket
chassis flange
bracket cover
2
3
Connect the power plug at
the back of the drawer to the
power outlet.
Place the warming drawer
carefully inside the cabinetry.
5
Remove the backing of
adhesive tape on the door
frame.
Align the custom panel
carefully with the cabinetry.
spacer
15
9
INSTALLING THE DRAWER
7
6
Open the drawer fully, and remove
the T15 screws from both sides of
the door frame.
Slide the door frame up and off the
drawer.
8
Drill pilot holes into the custom panel
through the screw holes in the door
frame.
Be careful not to drill through the
panel.
Secure the custom panel to the door
frame with T15 wood screws (6x).
Slide the door frame back onto
the drawer and align the custom
panel vertically with surrounding
cabinetry.
Secure the door frame in place
with T15 screws.
Ensure the custom panel is
correctly aligned and centered
before fixing to the tape as this
can only be done once.
Use shims (not supplied) to ensure
gaps are accurate.
shims
16
ADJUSTING THE DEPTH ADJUSTING THE HEIGHT
Open the drawer fully.
Using a hex key, turn the adjustment
screw to move the front panel forward.
Turn clockwise to move backwards or
counterclockwise to move forwards.
1
2
The depth is adjustable within 4mm.
The depth of the front panel of the warming drawer can be adjusted to align with the
surrounding cabinetry.
Open the drawer fully, and slightly
loosen the T15 screws.
1
2
3
Adjust to the required height and then
re-tighten the screws. The height is
adjustable within 2mm.
Close the drawer and check the
alignment. Adjust again if necessary.
The front panel of the warming drawer can be adjusted vertically to align with the surrounding
cabinetry.
max 2mm
17
F the warming drawer is level and securely fitted to the cabinetry.
F any internal packaging has been removed from the drawer.
F the isolating switch is accessible to the customer.
F the bottom shelf can fully support the total weight of the combined appliances.
F Open the drawer.
F Press the
1h
2h
1h
2h
1h
2h
1h
2h
FP WARMER DRAWER INTERFACE LOGIC_V1
PRODUCT OFF
THE THREE TEMPERATURE BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER TWO BUTTONS SHOW WHITE
THE TWO TIMER BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER BUTTON SHOWS WHITE
ICE AND WATER INTERFACE COMPONENTS
All bezels capable of glowing white and red
except fot the on /o bezel which only needs
to glow red.
Component Layout As Shown.
USER PRESSES ON/OFF BUTTON
ALL OTHER BEZELS GLOW WHITE EXCEPT
TEMPERATURE SETTING WHICH IS PRESET TO
MEDIUM AND GLOWS RED (PRODUCT STARTS
HEATING TO THE MEDIUM TEMPERATURE)
ON/OFF GLOWS RED UNTIL BUTTON IS PRESSED
AGAIN SHUTTING THE PRODUCT OFF.
WHEN THE TIMER BUTTON IS PRESSED THE
PRODUCT IS SET TO RUN FOR THE ALLOWED
TIME.
WHEN THIS TIME RUNS OUT THE PRODUCT SHUTS
OFF.
1h
2h
1h
2h
button to turn the warming drawer on.
F Shut the drawer.
F After 5-10 minutes, open the drawer to ensure heating has started.
F Press the
1h
2h
1h
2h
1h
2h
1h
2h
FP WARMER DRAWER INTERFACE LOGIC_V1
PRODUCT OFF
THE THREE TEMPERATURE BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER TWO BUTTONS SHOW WHITE
THE TWO TIMER BUTTONS WORK AS A UNIT
ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,
THE OTHER BUTTON SHOWS WHITE
ICE AND WATER INTERFACE COMPONENTS
All bezels capable of glowing white and red
except fot the on /o bezel which only needs
to glow red.
Component Layout As Shown.
USER PRESSES ON/OFF BUTTON
ALL OTHER BEZELS GLOW WHITE EXCEPT
TEMPERATURE SETTING WHICH IS PRESET TO
MEDIUM AND GLOWS RED (PRODUCT STARTS
HEATING TO THE MEDIUM TEMPERATURE)
ON/OFF GLOWS RED UNTIL BUTTON IS PRESSED
AGAIN SHUTTING THE PRODUCT OFF.
WHEN THE TIMER BUTTON IS PRESSED THE
PRODUCT IS SET TO RUN FOR THE ALLOWED
TIME.
WHEN THIS TIME RUNS OUT THE PRODUCT SHUTS
OFF.
1h
2h
1h
2h
button to turn the warming drawer off and shut the drawer.
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date
INSTALLER CHECKLIST
IMPORTANT!
Read all installation instructions in this manual to see if the unit has been correctly installed.
Ensure that installation has been completed correctly before use.
Ensure that: Test operation:
592266A 08.20
FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2020. All rights reserved.
The models shown in this guide may not be available in all markets
and are subject to change at any time.
The product specifications in this guide apply to the specific products and
models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time.
For current details about model and specification availability in your country,
please go to our website or contact your local Fisher & Paykel dealer.
