Loading ...
Loading ...
Loading ...
The operation of any utilityvac can result in foreign objects
being blown into the eyes, which can result in severe eye
damage. Always wear safety goggles complying with ANSI
Z87.1 (shown on Package) before commencing operation.
Safety Goggles are available at Sears retail or catalog stores.
I WARNING: To avoid injury to bystandards, keep themclear of blowing debris.
To avoid hearing damage wear ear protectors when using the
vac forextended hours or when using it ina noisyarea.
Blowing Feature
Your vac features "Full Blowing", it has the capability to blow
sawdust and other debris. Follow the steps below to use your
vac as a blower.
1. Locateblowing pert of your vac.
2. Insert soft end of your hose intoblowing pert.
3. (Optional) Attach extension wand to swivel end of hose, then
place a blower nozzle on the wand.
4.Turn vao on and you are ready to use your vao as a blower.
WARNING: Always wear safety goggles complying
with ANSI Z87.1 before using as a blower.
NOTE: Sears recommended accessories are available at
Sears retail or catalog stores. The Sears Blower Nozzle Stock
No. 9-16964 and extension handles Stock No. 9-16964 are
recommended for blowing debris.
on
Wand
(Optional)
"Blowing
Nozzle
(Optional)
WEAR YOUR
Filter Maintenance
WARNING: TO avoid injury from accidental starting,
unplug power cord before changing or cleaning filter.
NOTE: This filter is made of high quality paper designed to
stopvery small particles of dust. The filter can be used forwet
or dry pick up. Handle the filter carefully when removing to
clean or installingit, Creases inthe filterpleats may occur from
installation but creases will not affect the performance of the
filter.
Removal
To remove the old filter for cleaning or replacement:
1.Remove filter nut from the screw on the filter cage, remove
filter plate and lift off filter.
CAUTION: To avoid damage to the blower wheel,
always reinstall the filter before using the vac for dry
material pick-up.
Installation
(See page 4 "Filter Assembly")
WARNING: Do not remove the filter cage. It is there to
help prevent your fingers from getting into the blower
wheel.
Cleaning
Your filter should be cleaned often to maintain peak vac
performance.
NOTE: Be sure to dry the filter before storing or picking up dry
debris.
Dry Filter
1. Some removal of dry debris can be accomplished without
removingthe filterfrom the vac by slappingyour hand ontop
ofthe lidwhile the vac isoff,
2. Afterfilter removal fromvao, remove the drydebris by gently
tapping the filter against the inside wall of your dust drum
and the debris will loosen and fall.
NOTE: For best results of cleaning due to accumulated dust,
clean the filter in an open area. Cleaning SHOULD be done
outdoors and not inthe living quarters.
3. For thorough cleaning of dry filter with fine dust (no debris)
you may run water through itas described under "Wet Filter".
Wet Filter
After filter is removed, a wet filter should be cleaned by running
water through it from a hose or spigot. Take care that water
pressurefrom the hose is not strongenough todamage filter.
IMPORTANT: You can quickly dry the filter by runningthe vac
without the hose assembly attached for approximately 10
minuteswith filter in place to speed up drying. Check the filter
for tears or small holes, Even a small hole can cause a lot of
dust to come out of your vac. Do not use a filter with holes or
tears in it. Replace it immediately.
Wet/Dry Vac Maintenance
To keep your Wet/Dry Vac looking its pest, clean the outside
with a cloth dampened with warm water and mild soap, to
clean the drum:
3. Wipe outwith drycloth.
IMPORTANT:To assure product SAFETY and RELIABILITY,
repairs and adjustment should by performed by Sears Service
Centers, always using Sears replacement parts.
1.Dump debris out.
2. Wash drum thoroughly. 6
Loading ...
Loading ...