Loading ...
Loading ...
Loading ...
FOR YOUR SAFETY READ BEFORE LIGHTING
explosion may result causing property damage, personal injury or loss of life.
BEFORE OPERATING: ENTIRE SYSTEM MUST BE FILLED WITH WATER AND AIR PURGED FROM ALL LINES.
A. This appliance has apilotwhich must be lightedby hand.
When lighting the pilot, follow these instructions exactly.
If you cannot reach your gas supplier, call the fire
department.
B. BEFORE LIGHTING smellall around theappliance area
forgas. Besure to smell next to the floor because some
gas is heavier than air and will settle onthe floor.
WHATTO DO IFYOU SMELL GAS:
Do not tryto light any appliance.
Do not touch any electric switch; do not use any phone
in your building.
Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. Ifthe knob will not push in orturn
by hand, don't try to repair it, call a qualified service
technician. Forceor attempted repairmay result ina fire
or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
LIGHTING INSTRUCTIONS
GAS CONTROL KNOB
PI_O
]GNITEI_
_ENERATOR
THERMOSTAT
121{AL
GAS CONTROL
FIGURE "A" FIGURE "B" FIGURE "C"
"OFFPOSITION "PILOT" POSITION "ON" POSITION
TOP KNOB
MAIN BURNER
/
FIGURE "D"
1. (_ STOP! Readthesafetyinformation
above onthis label.
2. Set the thermostat to lowest setting (PILOT LIGHTING).
Turn thermostat dial fully clockwise f'_ until it stops.
3. Pushthe gascontrol knobdown slightly andturn clockwise
f'_ to"OFF", SEE FIGURE "A".
NOTE: Knob CANNOT beturned from "PILOT" to "OFF"
unless it ispushed down slightly. Do not force.
4. Remove the outer burner door located below the gas
control.
5. Wait five (5) minutes to clear out any gas. Ifyou then
smell gas, (_) STOP! Follow"B"in the safety information
above on this label, if you don't smell gas, goto next step.
6. This unitisequipped with apush button pilotigniter,which
is used to light the pilot. Locate the igniter on the gas
control.
7. Turn gas control knob counterclockwise _ to"PILOT",
SEE FIGURE'13".
8. The pilot islocated onthe rightsideofthe burner.Itcan be
located by looking through the glass view port while
pressing the piezo igniter buttonseveral times. Lookfor a
spark atthe pilot ]ocetion, FIGURE"D".
9. Once the pilot has been found, push the gas knob all the
way down. Immediately pressthe pilotigniter button rapidly
(4) to (5) times. If the pilot will not light, repeat step (3)
through (9).
10. Continue to hold the gas centrol koob down for about one
(1) minute after the pilot islit. Release the gas control knob
and itwill popback up. Pilotshould remainlit. If itgoes out,
repeat step (3)through (9). Itmay take several minutes for
air to clear the lines before the pilot will light.
If knob does not pop up when released, stop and
immediately call your service technician or gas supplier.
Ifthe pilot will not stay lit after several tries, turn the gas
control knob clockwise t_ to"OFF" and call your service
technician orgas supplier.SEE F]GURE"A".
11. Once the pilotflame isestablished replace theouter burner
door.
12. At arms length away, turn gas control knob
counterclockwise _ to"ON". SEE FIGURE"C".
13. Set thermostat to desired setting.
DANGER: Hotter water increases the risk of
scald injury. Consult the instruction manual
before changing temperature.
TO TURN OFF GAS TO APPLIANCE
2 Push gas oontrol knob down shghtly and turn clockwise
I1. Setthermostat tothe lowest setting(PILOTLIGHTING). " .... " .... '
t_ to OFF. Donotforce. SEEFIGURE A.
18
Loading ...
Loading ...
Loading ...