Loading ...
Loading ...
Loading ...
AIRCONDITIONERUSE
Operating your air conditioner properly helps you to obtain the
best possible results.
This section explains proper air conditioner operation.
IMPORTANT:
• If you turn off the air conditioner wait at least 3 minutes
before turning it back on. This keeps the air conditioner from
blowing a fuse or tripping a circuit breaker.
• Do not try to operate your air conditioner in the Cool, Eco or
Overnight mode when outside temperature is below 65°F
(18°C). The inside evaporator coil will freeze up, and the air
conditioner will not operate properly.
NOTE: In the event of a power failure, your air conditioner will
operate at the previous settings when the power is restored.
POWer Modes @ Cool
, ...... _ Eco
'O" "-_6 (2bO .... ight
• . . [
_Fan Only
Fan Speed
@
Timed
On Off
Set Clock
J
NOTE: When the air conditioner is in Standby mode, the red
Power LED will be lit.
1. Press POWER to turn on the air conditioner. The red Power
LED will change to blue.
POWer
"0.i:
NOTE: When the air conditioner is first plugged in, the display
will show ]AM for 30 seconds, until the clock is set to the
correct time or a new mode is selected. When the air
conditioner is turned on for the first time after it is plugged in,
the mode will be set to Cool and the fan speed will be set to
Auto.
2.
3.
4.
The display will show the factory-set temperature of 72°F
(22°C) for 5 seconds and then will show the current room
temperature.
When the air conditioner is turned on at all other times, the
unit will run according to the previous settings. The display
will show the previous settings for 5 seconds, and then show
the current room temperature.
Select mode. See "Mode."
Set temperature. See "Temperature."
Select fan speed. See "Fan Speed."
NOTES:
• Auto fan speed and Temperature cannot be selected in
Fan Only mode.
• In Eco and Cool modes, Auto fan speed is selected
automatically.
Mode
1. Press MODE until you see the indicator light glow for the
desired setting.
2. Choose Cool, Eco, Overnight, Fan Only or 6thSense TM Mode.
NOTE: 6thSense can be accessed only when you are using
the remote control.
• Cool--Cools the room. Automatically sets fan speed to
Auto. Press the up or down arrow button to adjust the
temperature.
• Eco--Saves energy. The compressor and fan runs until
the set temperature is reached, and then the compressor
turns off. The fan runs an additional minute before turning
off. Automatically sets the fan speed to Auto. Press the
up or down arrow button to adjust the temperature.
• Overnight (8 hours)--Automatically raises the set
temperature by 4°F (2°C) and sets the fan speed to Low.
Press the up or down arrow button to adjust the
temperature. The set temperature increases 2°F (1°C) per
hour during the first 2 hours, and remains at this
temperature setting for the next 6 hours.
When Overnight mode ends, the air conditioner will go
into Cool mode and the thermostat setting will return to
the original Overnight mode temperature setting.
NOTE: The LEDs on the control panel will power down
10 seconds after Overnight mode is set. To reactivate the
LEDs and illuminate the control panel, touch any button
on the control panel or the remote control.
• Fan Only--Only the fan runs. Press FAN SPEED to select
Low, Medium or High. The Bar LED shows 1 bar for Low,
2 bars for Medium and 3 bars for High fan speed. The
temperature display shows "1" for Low, "2" for Medium
and "3" for High fan speed. After 5 seconds, the display
shows the current room temperature.
NOTES:
• Auto fan speed and Temperature cannot be selected
in Fan Only mode.
• In Eco and Cool modes, Auto fan speed is selected
automatically.
6thSense TM System--See "Using the Remote Control."
Modes €- coo+
j_ _Eco
. -_ (_ Overnight
_Fan Only
NOTE: After 5 seconds, display will show the current room
temperature.
13
Loading ...
Loading ...
Loading ...