Loading ...
Loading ...
Loading ...
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.maytag.com/product_help -
in Canada www.maytag.ca for assistance and to possibly avoid a service call.
if you experience
Once any possible issues are corrected, touch POWER/CANCEL once to clear the code. Reselect and restart the cycle.
"Sud" (Excess suds)
appears in display
Excessive suds in washer. Washer is
running a suds reduction routine.
Allow the washer to continue. Use only HE detergent.
Always measure detergent, and base detergent quantity on
load size. Follow detergent manufacturer's instructions.
Touch WATER HARDNESS to change water hardness to "soft_'
"dEt" (Detergent) The dispenser cartridge is not Ensure the dispenser cartridge is inserted correctly and the
appears in display detected, dispenser drawer is shut completely. For single-load doses of
detergent, ignore this message.
Check for proper water supply.
Fn8 followed by En/
(water supply error)
appears in display
Check plumbing for correct drain hose
installation. Drain hose extends into
standpipe farther than 41_'' (114 mm).
Fn9 followed by En/
(drain pump system
error) appears in display
Both hoses must be attached and have water flowing to the inlet valve.
Both hot and cold water faucets must be on.
inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
TouchPOWER/CANCEL onceto clearthe code.Thentouch POWER/
CANCEL againto restartwasher.If code appears again,call for service.
Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked.
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above the floor.
Not using HE detergent or using too Use only HE detergent. Always measure detergent and follow
much HE detergent, manufacturer's directions based on load size and soil level.
FL75 followed by En2 Washer door not locking. Touch POWER/CANCEL to cancel the cycle. Make sure the door is
(door will not lock) closed completely and latching. Check for items in the washer drum
appears in display that may be keeping the door from closing completely.
"rL" (remove load) Load detected in drum during Clean Remove items from washer drum and restart Clean Washer with
appears in display Washer with affresh "j cycle, affresh _-_cycle.
The three detergent level Detergent dispenser is not securely in Pull out the dispenser and slide it back in place.
status lights are lit place.
Detergent Level sensor error. Touch POWER/CANCEL to reset system, if this fails, unplug
washer or disconnect power for one minute, then plug in washer or
reconnect power.
Washer making error Door has not been opened and closed This code may appear when the washer is first turned on.
beeps for at least 3 cycles. Open and close the door to clear the display.
Washer beeps when Door not closed. Close the door completely.
START is touched
F## E## code other System error code. Touch POWER/CANCEL once to clear the code. Then touch
than as described above POWER/CANCEL again to restart washer, if code appears again,
appears in display call for service.
"lnt" (interrupted) The cycle was paused or cancelled. The washer can take 20 to 30 minutes to stop spinning
appears in display and drain and will display this error code during that time.
Touch POWER/CANCEL once to clear the code. Then touch
POWER/CANCEL again to restart washer.
Clean Washer LED
flashing at end of wash
cycle
The washer has run 30 wash cycles and
is indicating a reminder to run the Clean
Washer with affresh "j cycle.
Run the Clean Washer with affresh "_cycle, if the Clean Washer with
affresh _-_cycle is not turned on, the LED will stop flashing at the end
of a wash cycle after running 3 more regular wash cycles. After 30
more wash cycles are completed, the Clean Washer LED will again
flash at the end of a wash cycle as a reminder.
J
18
Loading ...
Loading ...
Loading ...