Loading ...
Loading ...
Loading ...
- 9 -
11/2020
Copyright © 2020, Fast ČR, a.s.
INSERTING AND REPLACING BATTERIES IN THE REMOTE CONTROL
■ Push down the latch of cover C13 on the rear side of the remote control C1 to
release it and remove the cover.
■ Insert two type AAA (1.5 V) batteries into the remote control. When inserting the
batteries, ensure the correct polarity as shown inside the battery compartment C14.
Put the cover C13 back on and click it into place.
■ In the event that the batteries are flat, replace them with new ones. Do not combine
various types of batteries or new and old batteries.
■ The signal range of the remote control is approximately 6 m.
SETTING SYSTEM TIME ON THE REMOTE CONTROL
■ The system time of the vacuum cleaner is the actual time according to your time
zone. It must be correctly set if you wish to use the scheduled cleaning function.
■ In the stand-by mode or in the charging in the charging station mode, hold down
button C11 (CLK) until the time setting value (hours and minutes) starts flashing
on the display C2.
■ Using buttons C5 ( ) or C8 ( ) set the time values. Toggle between the hour and
minute numbers using buttons E6 ( ) or C7 ( ).
■ Confirm the set time by pressing button C11 (CLK). The appliance will beep 1x and
the set time will be saved to the memory of the remote control as the system time.
■ If you do not perform any changes within 10 seconds, the system time setting mode
will automatically be cancelled and the time will not be saved to memory.
OPERATING THE ROBOTIC VACUUM CLEANER
Note:
Before starting the vacuum cleaner, always make sure that either
the dust container A5 or the complete mop unit A6 including the
respective HEPA dust filters is inserted inside.
TURNING ON THE ROBOTIC VACUUM CLEANER
■ Turn on the power supply to the vacuum cleaner using the main switch A4.
■ Press button A1. The button'sindicator will start flashing blue. This sets the vacuum
cleaner to stand-by mode and it is ready for operation.
STAND-BY MODE
■ The stand-by mode means that the vacuum cleaner is ready for operation. Button
A1 is flashing blue.
■ Set the vacuum cleaner to the stand-by mode by pressing button A1 on the vacuum
cleaner or buttons C9 (ON/OFF) on the remote control either by turning on the
power supply using main switch or whenever while the vacuum cleaner is running.
SLEEP MODE
■ The sleep mode serves to save the battery'scapacity. Put the vacuum cleaner into
sleep mode:
- by holding down button A1 for longer than 3 seconds.
- automatically after one minute of inactivity
- automatically when the battery voltage is too low and the vacuum cleaner is unable
to dock in the charging station.
■ In sleep mode the backlight of button A1 will turn off. To wake the vacuum cleaner
from the sleep mode to the stand-by mode, press button A1 on the vacuum cleaner
or the control button C9 (ON/OFF) on the remote control.
Note:
When the vacuum cleaner is in sleep mode, it is not possible to wake it
up using the mobile phone application. In sleep mode, it reacts only to
buttons A1 or C9 (ON/OFF) on the remote control.
TURNING OFF THE ROBOTIC VACUUM CLEANER
■ If you wish to completely turn off the vacuum cleaner, set the main switch A4 to
position 0 (off ). The backlight on button A1 will turn off and the power supply will
be shut off. When the vacuum cleaner is turned off, it will not respond to any button.
SELECTING THE ROBOTIC VACUUM CLEANER CLEANING MODE
■ Before starting the cleaning process, check that the entry door into your apartment
or house is closed. From the floor surfaces, remove clothing, paper, toys, power or
extension cords and other items that the vacuum cleaner could suck in or catch.
Lift curtains and drapes that reach to the floor so that the vacuum cleaner does not
catch them.
Tip:
When vacuuming in a new environment for the first time, carefully
observe the movement of the vacuum cleaner. You can thereby
recognise problematic obstacles and remove them for the next
cleaning session.
AUTOMATIC CLEANING MODE
■ Press button A1 or button C9 (ON/OFF) on the remote control. The vacuum cleaner
will enter the automatic cleaning mode, in which it effectively combines various
routes to achieve an optimal clean of the entire floor area. As soon as the vacuum
cleaner finishes cleaning, it will seek out the charging station and dock there to
recharge.
MAXIMUM POWER MODE
■ Press button C12 (MAX) on the remote control. The vacuum cleaner will enter the
cleaning mode, in which it effectively combines various routes to achieve an optimal
clean of the entire floor area. This mode is characterised by increased motor and
central rotary brush power for the purpose of achieving the most effective cleaning
process.
SPIRAL CLEANING MODE
■ Press button C10 (MODE) on the remote control so that display E2 shows MODE1.
The vacuum cleaner will enter the spiral cleaning mode. Compared to the other
modes, this mode is characterised by a lower speed of the vacuum cleaner and
increased motor and central rotary brush power for the purpose of achieving the
most effective cleaning process.
RANDOM DIRECTION MOVEMENT MODE
■ Repeatedly press button C10 (MODE) on the remote control so that display C2
shows MODE2. The vacuum cleaner will enter the random direction movement
mode and will continue cleaning in this mode until the battery is almost flat. It
will then end the cleaning process and seek out the charging station in order to
recharge itself.
ALONG-THE-WALLS CLEANING MODE
■ Repeatedly press button C10 (MODE) on the remote control so that display C2
shows MODE3. The vacuum cleaner will enter the along-the-walls cleaning mode,
in which it moves along the perimeter of the room and the motorised side rotary
brushes sweep out the dirt along the walls, furniture corners to achieve aperfect
clean. The vacuum cleaner will continue cleaning until the battery is almost flat. It
will then end the cleaning process and seek out the charging station in order to
recharge itself.
ZIG-ZAG CLEANING MODE
■ Repeatedly press button C10 (MODE) on the remote control so that display C2
shows MODE4. The vacuum cleaner will enter the zig-zag cleaning mode, which is
suitable for effectively cleaning large areas without furniture present. The vacuum
cleaner will continue cleaning until the battery is almost flat. It will then end the
cleaning process and seek out the charging station in order to recharge itself.
PAUSING THE CLEANING PROCESS
■ Press button A1 or C9 (ON/OFF) on the remote control at any time during the
cleaning process to stop the vacuum cleaner in the place where it is cleaning.
USING THE MOP UNIT
■ The mop unit is used for simultaneous vacuuming and dry or wet wiping of smooth
floor surfaces. It consists of the removable dust container D1, water tank D2 and the
mop fabric D3. The water tank is equipped with an electronically-controlled water
pump that automatically doses the water on to the fabric and also stops dosing
water at the end of the cleaning process to prevent water from leaking on to the
floor or the charging station.
Attention:
Only use the mop unit intended for this robotic vacuum cleaner
model.
Do not use the water tank D2 without the mop fabric attached.
The mop unit is not intended for cleaning carpets.
Dry wiping of floors
■ Dry wiping is used for removing fine dust and floor polishing.
■ If the mop unit is inserted inside the vacuum cleaner, press latch A7 and slide the
unit out of the vacuum cleaner.
■ Attach the mop fabric to the underside of the water tank using the velcro zip D4 on
the water tank and insert the unit back into the vacuum cleaner.
■ Start the vacuum cleaner.
Wet wiping of floors
■ Wet wiping is used for cleaning away minor dirt and floor polishing
■ If the mop unit is inserted inside the vacuum cleaner, press latch A7 and slide the
unit out of the vacuum cleaner.
■ Slide the dust container out of the water tank.
■ Attach the mop fabric to the underside of the water tank using the velcro zip D4
on the water tank.
■ Open the cap D5 and fill the tank with water. Properly insert the cap back in. Wipe
any excess water off the water tank. Take special care to ensure that the contacts
D6 are dry.
Note:
For wiping, we recommend using clean water. If you use a cleaning
agent, it may foam up and thereby worsen the dripping of the water
on to the fabric, or potentially cause smudges on the floor after it dries.
■ Insert the dust container back into the water tank and insert this assembly back into
the vacuum cleaner.
■ Start the vacuum cleaner.
SCHEDULED CLEANING
Note:
The scheduled cleaning time setting is based on the system time set on
the remote control. Therefore, before setting the scheduled cleaning
time, it is necessary to correctly set the system time as described in
chapter SETTING SYSTEM TIME ON THE REMOTE CONTROL
■ This function is used to set atime, when the vacuum cleaner is to start automatic
cleaning. The vacuum cleaner will then start cleaning at the same time every day.
If you use the application, it is possible to schedule acleaning time for every day at
adifferent time. Please follow the instructions in the application.
Loading ...
Loading ...