Loading ...
Loading ...
Loading ...
15
English
Versatrack™ (Fig. J, Q)
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
WARNING: To reduce the risk of serious personal injury,
do not use a damaged Versatrack™ integral hang hook
or Versatrack™ Trackwall. A damaged Versatrack™
integral hang hook or Versatrack™ Trackwall will not
support the weight of thetool.
WARNING: To reduce the risk of serious personal injury,
DO NOT suspend tool overhead or suspend objects
from the integral hang hook. ONLY suspend tool on the
Versatrack™ Trackwall using the integral hanghook.
WARNING: The Versatrack™ integral hang hook
is intended to mount the tool onto a Versatrack™
Trackwall rail. Do not use the integral hang hook to
mount the tool to any othersurface.
WARNING: The Versatrack™ integral hang hook is not
a belthook.
WARNING: When hanging objects on a Versatrack™
Trackwall rail, adequately space the tools in order to not
exceed 75 lb (35 kg) per linearfoot.
WARNING: Before using the tool make sure that
the Versatrack™ integral hang hook is returned to its
originalposition.
iMPORTAnT: Versatrack™ accessories mount compatible
tools securely to the Versatrack™ Trackwallsystem.
1. Turn tool off, remove the battery pack and
removeaccessories.
2. Install guide bar scabbard
12
onto the guide bar
4
.
CAUTION: Any product with exposed cutting teeth
must have them covered securely if it is to be on
theVersatrack™Trackwall.
3. Flip or pull open the integral hang hook
22
. It clicks
when locked intoposition.
4. Mount the integral hang hook to the
Versatrack™Trackwall.
nOTE: Versatrack™ accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN, call 1-888-331-4569.
Accessories
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with thisproduct.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact CRAFTSMAN call 1-888-331-4569 .
Saw Chain and Guide Bar
After every few hours of use, remove the sprocket cover,
guide bar and chain and clean thoroughly using a soft bristle
brush. Ensure oiling hole on bar is clear of debris. When
replacing dull chains with sharp chains it is good practice to
flip the chain bar from bottom totop.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1approved eye
protection when performingthisprocedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into aliquid.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
• When supported at one end first, cut 1/3 the diameter
from the underside (underbuck). Then make the finishing
cut by overbucking to meet the firstcut as shownbelow.
1
1
2
2nd CUT OVERBUCK
(2/3 DIAMETER)
TO MEET 1st CUT
(TO AVOID PINCHING)
1st CUT UNDERBUCK
(1/3 DIAMETER)
AVOID SPLINTERING
• When supported at bothends. First, cut 1/3 down from the
top overbuck. Then make the finished cut by underbucking
the lower 2/3 to meet the firstcut as shownbelow.
2nd CUT UNDERBUCK
(2/3 DIAMETER)
TO MEET 1st CUT
(TO AVOID PINCHING)
1st CUT OVERBUCK
(1/3 DIAMETER)
TO AVOID SPLINTERING
• When on a slope always stand on the uphill side of
the log. When “cutting through”, to maintain complete
control reduce the cutting pressure near the end of the
cut without relaxing your grip on the chain saw handles.
Don’t let the chain contact the ground. After completing
the cut, wait for the saw chain to stop before you move
the chain saw. Always stop the motor before moving
from cut tocut.
Loading ...
Loading ...
Loading ...