Loading ...
Loading ...
Loading ...
13
English
Common Cutting Techniques
Felling
The process of cutting down a tree. Do not fell trees in high
windconditions.
WARNING: Felling can result in injury. It should only be
performed by a trainedperson.
• A retreat path should be planned and cleared as
necessary before cuts are started. The retreat path should
• Guard Against Kickback which can result in severe
injury or death. See Important Safety Instructions
guard Against Kickback, to avoid the risk
ofkickback.
• Do not overreach. Do not cut above chest height.
Make sure your footing is firm. Keep feet apart.
Divide your weight evenly on bothfeet.
• Use a firm grip with your left hand on the front
handle
14
and your right hand on the rear
handle
13
so that your body is to the left of the
guidebar.
• Do not hold chain saw by front hand guard
3
.
Keep elbow of left arm locked so that left arm is
straight to withstand akickback.
WARNING: Never use a cross‑handed grip (left hand
on the rear handle and right hand on the fronthandle).
WARNING: Never allow any part of your body to
be in line with the guide bar
4
when operating the
chainsaw.
• Never operate while in a tree, in any awkward
position or on a ladder or other unstable surface.
You may lose control of saw causing severeinjury.
• Keep the chain saw running at full speed the entire
time you arecutting.
• Allow the chain to cut for you. Exert only light
pressure. Do not put pressure on chain saw at end
ofcut.
WARNING: When not in use always have
the chain brake (if equipped) engaged and
batteryremoved.
ON/OFF Switch (Fig.M)
Always be sure of your footing and grip the chain saw firmly
with both hands with the thumb and fingers encircling
bothhandles.
1. To turn the unit on, push down on the the lock off lever
2
,
shown in Fig.M, and squeeze the trigger switch
1
. Once
the unit is running, you may release the lock offlever.
2. In order to keep the unit running you must continue
to squeeze the trigger. To turn the unit off, release
thetrigger.
nOTE: If too much force is applied while making a cut the
saw will turn off. To restart saw, you must release the lock off
lever
2
and the trigger switch
1
before the saw will restart.
Begin your cut again this time with less force. Allow the saw
to cut at its ownpace.
WARNING: Never attempt to lock a switch in the
ONposition.
Operating the Chainsaw (Fig.L)
WARNING: Read and understand all instructions.
Failure to follow all instructions listed below may result
in electric shock, fire and/or serious personalinjury.
Proper hand position requires the left hand on the front
handle
14
, with the right hand on the rear handle
13
.
Proper Hand Position (Fig. L)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position asshown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
suddenreaction.
Installing and Removing the Battery Pack
(Fig.E)
nOTE: For best results, make sure your battery pack is
fullycharged.
To install the battery pack
7
into the tool handle, align the
battery pack with the rails inside the tool’s handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does notdisengage.
To remove the battery pack from the tool, press the release
button
16
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of thismanual.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can causeinjury.
Transporting Chainsaw (Fig.J)
• Always turn unit off, remove the battery and cover the
guide bar
4
with the scabbard
12
when transporting
thesaw.
The oil level indicator
11
shows the level of the oil in the
chainsaw. If the oil level is less than a quarter full, remove the
battery from the chainsaw and refill with the correct type of
oil. Always empty oil tank when finishedcutting.
nOTE: Use a high quality bar and chain oil for proper saw
chain and bar lubrication. As a temporary substitute, a non-
detergent SAE30 weight motor oil can be used. The use of
a vegetable based bar and chain oil is recommended when
pruning trees. Mineral oil is not recommended because it
may harm trees. Never use waste oil or very thick oil. These
may damage yourchainsaw.
Filling the Oil Reservoir
1. Unscrew counterclockwise and then remove the oil cap
10
.
Fill the reservoir with the recommended bar and chain oil until
the oil level has reached the top of the oil level indicator
11
.
2. Refit the oil cap and tightenclockwise.
3. Periodically switch the chainsaw off and check the oil
level indicator to ensure the bar and chain are being
properlyoiled.
Loading ...
Loading ...
Loading ...