Loading ...
Loading ...
Loading ...
4. TEMP- V
° Pressing this button in cooling mode decreases the desired room
temperature setting by ]°F (]°C) down to a minimum setting of 63°F
(17°C).
° Pressing this button in heating mode decreases the desired room
temperature setting by ]°F (]°C) down to a minimum setting of 59°F (15°C).
5. LED DISPLAY
The display shows the current temperature setting.
By pressing the (A) or (V) buttons, the temperature setting can be changed.
When pressing the timer button ((_), the number of hours is shown until
delayed start-up or delayed shutdown. After each setting, the display returns
to showing the current temperature setting. In the dehumidifying mode,
"dh" is shown on the display. Error codes are also shown in the display. See
Troubleshooting section for Error code definitions.
6. SPEED _
Pressing this button sets the ventilator fan speed to "_ (low)", " _-'_ (medium)",
(high)" or "/.._ (automatic)".
When (/__) is selected:
° If the set temperature is more than 16.2 ° F ( 9 ° C) different than room
temperature, the fan wiil run at fuil speed.
° If the set temperature is less than 9 ° F (4 ° C) different than room
temperature, the fan wiil run at medium speed.
• When the set temperature is reached, the fan wiiI run at low speed.
When the temperature becomes more than 9 ° F (4°C) different than
room temperature, the fan wiiI change to medium speed.
7. TIMER (_
Programmable timer button for delayed start-up or delayed shutdown.
How to program a delayed start-up
This function is used to set the number of hours delay before the appliance
comes on. Proceed as follows:
° With the power ON, select the desired Mode of operation (Cool, Heat
or Dehumidify)
° Turn the power OFF.
° Press the TIMER button ("00" wili blink in the display). While the
display is blinking, use the up and down buttons to set the number of
hours delay before the unit begins operation.
° Wait a few seconds for the display to show the set temperature. Use
the up and down buttons to adjust the set temperature if desired.
° After the set number of hours has expired, the unit starts automatically.
NOTE: If you press the POWER button before the set delay time has expired,
the delay setting wili cancel and the unit wili immediately turn ON.
How to program a delayed shutdown
This function is used to set the number of hours delay before the appliance shuts off.
Proceed as follows:
• With the power ON_ select the desired Mode of operation (Cool_ Heat or
Dehumidify).
Pressthe TIMER button ("00" will blink in the display). While the display is
blinkin% use the up and down buttons to set the desired number of hours until
shutdown.
Wait a few seconds for the display to show the set temperature. Use the up
and down buttons to adjust the set temperature if desired.
After the set number of hours has expired_ the unit shuts down automatically.
NOTE: If you press the POWER button before the set shutdown time has expired_ the
unit will shut down immediately.
8. SLEEP (_ zz
The Sleep mode is ideal for nighttime operation_ as it automatically reduces the fan
speed and minimizes the compressor runnin% for the quietest operation.
While the unit is ON_ press the SLEEPmode button. The unit will switch to low fan
speed.
In COOLING mode_ the temperature setting automatically increases by 2° F (1° C)
each hour for the first two hours of operation. As a resuih the Sbep function provides
most cooling when you first go to bed. The two setting increases whib you are sleeping
compensate for the typical decrease in ambient temperature as the night progresses.
If the ambient temperature becomes 2 ° F (1° C) cooler than the temperature settin%
the compressor will turn off. The compressor turns back on when the ambient
temperature becomes 2° F (1° C) warmer than the ambient temperature.
In HEATING mode_ the temperature setting is automatically DECREASED like above_
and the compressor turns off if the ambient temperature becomes 2° F (1° C) BELOW
the setting.
If desired_ the fan speed can be manually changed whib in SLEEPmode.
SLEEPmode cannot be activated whib the unit is in DEHUMIDIFY mode.
INSERTING BATTERIES - This remote control uses two AAA batteries.
° Remove the back cover of the remote control
° Insert two AAA ].5V batteries, making sure they are in the correct
position (see instructions inside battery compartment).
• Replace the cover.
DO NOT mix old and new batteries. DO NOT mix together Alkaline,
Standard (Carbon-Zinc), or Rechargable (Nickel-Cadmium) batteries.
Dispose of batteries properly. DO NOT leave batteries in the remote if it wili
not be used for longer than 2 months.
12 13
Loading ...
Loading ...
Loading ...