Loading ...
Loading ...
CLEANING
1. Some stainless steel parts may have a plastic protective wrap which must be removed. All stainless steel parts
should be washed thoroughly with hot, soapy water and with a liquid cleaner designed for this material to remove
film residues. If build-up occurs, do not use steel wool, abrasive cloths, cleaners, or powders! If it is necessary to
scrape stainless steel to remove encrusted material, soak with hot, wet cloths to loosen the material, then use a
wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape stainless steel!
Scratches are almost impossible to remove. Do not permit citrus or tomato juice to remain on a stainless steel
surface. Wipe any spills immediately. Citric acid will permanently discolor stainless steel.
2. Wash painted parts with warm soapy water. Do not use steel wool, abrasive cleaners, ammonia, or acids which may
damage the finish.
3. CAUTION: All brass special ordered parts are coated with an epoxy coating. DO NOT USE BRASS OR ABRASIVE
CLEANERS ON THE BRASS OPTION PARTS. All brass parts should be wiped regularly with hot soapy water.
When hot soapy will not do the job, use every day household cleaners that are not abrasive.
SERVICE INFORMATION
It is assumed that your multi-use chamber has been properly installed in accordance with all specifications. If your
multi-use chamber should fail to operate properly:
•Call you dealer or authorized service agency. The name of the authorized service agency can be obtained from the
dealer or distributor in your area.
•Have the following information readily available
a. Date purchased
b. Name of dealer from whom purchased.
•Clearly describe the problem you are experiencing.
If you are unable to obtain the name of an authorized serice agency, or if you continue to have service problems,
contact Viking Range Corporation at (662) 451-4133 or write to:
VIKING RANGE CORPORATION
PREFERRED SERVICE
111 Front Street
Greenwood, Mississippi (MS) 38930 USA
Record the following information indicated below. You will need it if service is ever required. The serial number and
model number are located on the interior back wall in the bottom left hand corner.
Date of Purchase Date Installed
Dealer’s Name
Address
If service requires installation of parts, use only authorized parts to ensure protection under the warranty. Replacement
parts are available from factory authorized parts distributors.
This manual should remain with the multi-use chamber for future reference.
USABLE SPACE INSIDE MULTI-USE CHAMBER
Two usable space options are given due to the location of the hinges for the upswing door. When using with a
microwave, allow adequate clearance for the opening of the microwave door. The chamber can also be used to store
cookbooks, small kitchen appliances, a television set, and other household items.
27” W. Models 30” W. Models
A B A B
Max. Height 12 3/4” (32.4 cm) 15” (38.1 cm) 12 3/4” (30.5 cm) 15” (38.1 cm)
Max. Width 23 5/8” (60.0 cm) 22 3/4” (57.8 cm) 26 5/8” (67.6 cm) 25 3/4” (65.4 cm)
Depth 22 1/2” (57.2 cm) 22 1/2” (57.2 cm) 22 1/2” (57.2 cm) 22 1/2” (57.2 cm)
Option A
Option B
Hinge
Hinge
Hinge
Hinge
4 5
HINGE ADJUSTMENTS
Vertical
Adjustment
Pitch
Adjustment
Horizontal
Adjustment
To adjust the door up or down, loosen the retainer
screws and adjust the vertical adjustment screws to the
desired position. Retighten the retainer screws.
To adjust the door in or out, loosen the retainer screws
and adjust the horizontal adjustment screws to the
desired position. Retighten the retainer screws.
To adjust the pitch of the door and sides of the chamber,
loosen the retainer screws and adjust the pitch
adjustment screws to the desired position. Retighten the
retainer screws
Retainer
Screws
Loading ...