Loading ...
Loading ...
Loading ...
ELECTRONIC CONTROLS SET-UP iNSTRUCTiONS
H.00 EXTRARINSEUpgradePrice- Increaseor decreasebetween0
EXTRA and200by pressingthe LEFTUPPERor RIGHTUPPERkeypad.
RINSE Factorypresetfor 1 coins= $0.25.
-> Pressthe LEFTMIDDLEkeypad onceto advanceto nextcode.
J.Cd COIN/DEBITOPTION
J.Cd Bothcoin &debit selected.
J.C Coinsselected,debitdisabled.Pressthe LEFTLOWERkeypad
3 timesfor thisselection.
J.d DebitCardselected,coinsdisabled.Pressthe LEFTLOWERkey
pad3 timesforthis selection.
J.Ed EnhancedDebitis self-selectedwhena Generation2 card reader
is installedinthe washer.TheEd optioncannotbe manually
selectedor deselected.
If cycle counter (9.0C) is selected, the following is true:
1 xx Number of cycles in THOUSANDS. 1 02 = 2,000
2xxx Number of cycles in ONES. 2225 = 225
TOTAL CYCLES = 2,225
This is "VIEW ONLY" and cannot be cleared.
Press the LOWER MIDDLE key pad once to advance
to next code.
If money counter (1.00 or 1.00) is selected, the following is
true:
3 xx Number in THOUSANDS. 3 01 = $1,000.00
4xxx Number in ONES. 4600 = $ 600.00
5 xx Number of HUNDRETHS. 5 75 = $ 00.75
TOTAL = $1,600.75
EXIT FROM SET-UP MODE
[] PD Models: Reinstall access door.
END OF SET-UP PROCEDURES
-->Pressthe LEFTMIDDLEkeypad onceto advanceto nextcode.
L.O0 PRICESUPPRESSIONOPTION
Thisoption causesthe customerdisplayto show 'ADD'or
'AVAILABLE'ratherthantheamountof moneyto add.(Used
mainlyindebit installations.)
L.00 NotSelected'OFF'. Table 1
L.PS Selected'ON'. Pressthe LEFTLOWERkey padonceforthis
selection.
.e Pressthe LEFTMIDDLEkeypad onceto advanceto nextcode.
n. CE CLEARESCROWOPTION
Whenselected,moneyheldin escrowfor 30 minuteswithout
furtherescrowor cycleactivitywill be cleared.
n. CE Selected'ON'.
n. 00 Notselected'OFF'.Pressthe LEFTLOWERkeypadonceto
deselectthisselection.
.e Pressthe LEFTMIDDLEkeypad onceto advanceto nextcode.
U.O0 COiN(HUNDREDTH)INCREMENTOFFSET
U.00 For usewithcard readerapplicationsonly.
-> Pressthe LEFTMIDDLEkeypad onceto advanceto nextcode.
A3.02 NORMALCycle Settings.Allowstheownerto selectthe cycle
defaultoptionsof WaterTemperature,SoilLevel,and ExtraRinse.
SeeTable1for specificsettings.Normalisset to 02 fromthe
factory.
A4.00 DELICATESCycleSettings.Allowstheownerto selectthe cycle
defaultoptionsof WaterTemperature,SoilLevel,and ExtraRinse.
SeeTable1for specificsettings.Delicatesis setto 00 from the
factory.
A5.OF POWERWASHCycleSettings.Allowsthe ownerto selectthe
cycledefaultoptionsof WaterTemperature,SoilLevel,andExtra
Rinse.
SeeTable1for specificsettings.Powerwashis setto OFfromthe
factory.
If preferred, just wait through 2 minutes of inactivity. All settings
will be saved and the display will revert to Select Cycle screen.
A3, A4, Extra Soil Wash A3,A4, Extra Soil Wash
or A5 Rinse Level Temp or A5 Rinse Level Temp
CO Off Off Cold 08 On Off Cold
O1 Off Off Cool 09 On Off Cool
02 Off Off Warm CA On Off Warm
03 Off Off Hot Ob On Off Hot
04 Off On Cold Oc On On Cold
05 Off On Cool Od On On Cool
06 Off On Warm OE On On Warm
07 Off On Hot OF On On Hot
Technician Service Access Code
This method is only available on washers set to free vend (6 00).
To enter service mode:
Press the LEFT UPPER, RIGHT LOWER, RIGHT UPPER, and
LEFT LOWER key pads within 10 seconds.
To exit service mode:
From service code 8.xx, press the LEFT UPPER key pad
for 4 seconds
or
Wait 2 minutes without touching any key pads (without diagnostic
modes running)
or
Power down the washer, then reapply power
NOTE: If a service cycle is in progress upon exiting service mode,
the cycle will complete normally with cycle status information
displayed. The display will resume normal customer operation
mode when the cycle ends.
19
Loading ...
Loading ...
Loading ...