Loading ...
Loading ...
All specications subject to change without notice.
Phone: (800) 793-0093www.dacor.com
PLANNING
GUIDE
4.12
Cabinet and Countertop Layout
WARNING
• To reduce the risk of personal injury caused by reaching
over a hot appliance, avoid locating cabinet storage space
directly above the cooktop.
• Failure to meet or exceed the maximum and minimum
dimensions/clearances stated in these instructions may
result in a fire hazard.
• Follow the countertop manufacturer’s instructions regarding
the minimum corner radius, use of heat reflective tape,
reinforcement of corners, etc.
◊ Carefully check the location where the cooktop will be installed.
For best performance, the cooktop should be placed away from
drafts that may be caused by doors, windows, and heating and air
conditioning vents.
◊ This appliance is to be used in conjunction with a suitable vent hood
or approved Dacor downdraft vent.
Refer to the following illustrations and notes for clearance allowances.
Model (A) Minimum (A) Recommended
DYCT304G 30” (76.2 cm) 36” (91.4 cm)
DYCT365G 36” (91.4 cm) 42” (106.7 cm)
Model
(B) Minimum to allow for clearance of hold-down
brackets
DYCT304G 29 in (73.7 cm)
DYCT365G 35 1/4 in (89.5 cm)
◊ Allow a minimum 1/4” (6 mm) clearance between the bottom of the
cooktop chassis and all combustible surfaces, including the upper
edge of a drawer inside the countertop cabinet below the cooktop.
◊ The gas supply piping, gas shut-off valve, and the electrical outlet
must be located so they do not interfere with the cooktop after it is
installed. If installing another appliance in the cabinet below, allow
for the routing of gas and electrical service behind it.
The installation must allow for the following:
◊ Access to the gas shut-off valve and regulator when the unit is
installed.
◊ The 40-inch (101.6 cm) power cord must be able to reach an
electrical outlet, and that electrical outlet must be easily accessible
after the cooktop is installed.
◊ Access to the underside of the cooktop for service and inspection
purposes.
◊ Clearance inside the counter to allow for correct installation of the
hold-down brackets.
To allow underneath access to the utilities and cooktop bottom, a fixed
shelf should not be installed below the cooktop. See the following pages
for countertop cutout dimensions.
Downdraft Compatibility
If installing the cooktop with a downdraft, use only the approved Dacor
downdraft model numbers below:
Cooktop Models Approved Downdraft Models
DYCT304G ERV3015, PRV30, or RV30
DYCT365G ERV3615, PRV36, or RV36
1/4” (6 mm)
min. height clearance
to combustible
surfaces
B
Underneath Cabinet Dimensions
Minimum Required Clearances
Around the Cooktop
13" max.
(33.0 cm)
3
Not required if side cabinets are 6 inches more than the left or right of both edges
of the cooktop. For DYGCT304, it is 5 1/2 inches (14.0 cm)
for DYGCT365. Allow 7 1/2” (19.1 cm) from cutout edge for RGC304,
7” (17.8 cm) for DYGCT365.
A
15" min.
1
(38.1 cm)
1 7/8" min.
(4.8 cm)
Combustible
surface to rear
Combustible overhead
cabinets
30" min.
1, 2
(76.2 cm)
See Note 3
See cutout
dimensions
2
If installing with an overhead vent hood, check the hood
installation instructions for specifications for minimum required clearances.
1
Measured from the cooking surface (top of cooktop grate).
1
Measured from the cooking surface (top of cooking grate).
2
If installing an overhead vent hood, check the hood
installation instructions for the minimum required clearance
specifications and requirements.
3
Not required if the side cabinets are at least 6 inches or
more from both sides of the cooktop.
All tolerances: +1/16” -0” unless otherwise noted.
All tolerances: +1/16” -0” unless otherwise noted.
DYCT304G, DYCT365G
Discovery
®
30” and 36” Wide
Drop-in Gas Cooktops
Document # PG04-009
Revised 12/14/15 Page 3/4
Loading ...