Loading ...
Loading ...
Loading ...
ADJ Products, LLC - www.adj.com - Vizi Beam RXONE Instruction Manual Page 35ADJ Products, LLC - www.adj.com - Vizi Beam RXONE Instruction Manual Page 34
The UC IR (sold separately) infrared remote gives you control of
various functions (See below). To control the fixture you must aim the
remote at the front of the fixture and be no more than 30 feet away.
Please see below for IR functions.
The Airstream IR (sold separately) remote transmitter plugs into
the headphone jack of your iOS phone or tablet. To control your IR
fixture you must raise the volume to the maximum on your iOS phone
or tablet and aim the transmitter at the fixture sensor and be no more
than 15 feet away. After you have purchased the Airstream IR trans-
mitters, the app is a free download from the app store for your iOS
phone or tablet. The app comes with 3 pages of control depending
on the fixture you are using. Please see below for IR functions includ-
ing the corresponding app page.
Works with App page 1.
STAND BY - Pressing this button will blackout the fixture. Press the
button again to return to the initial state.
FULL ON - Hold this button down to fully light up the unit. When you
let the button go, the unit will return to its previous state.
FADE/GOBO - This button activates gobo selection. Press this but-
ton and use buttons 1-9 to find your desired gobo.
“DIMMER +” and “DIMMER -” - These buttons are used to adjust
the output intensity in static color mode.
STROBE - Press and hold this button for strobing.
COLOR - This button activates color selection. Press this button and
use buttons 1-9 to find your desired color.
1-9 - Use buttons 1-9 to select your desired color when color selec-
tion is active, your desired gobo when gobo selection is active, and
your desired show when show mode is active.
SOUND ON & OFF - Use the buttons to activate and deactivate
sound active mode.
SHOW 0 - Press this button to activate show mode. Use buttons 1-4
to find your desired show.
Vizi Beam RXONE ADJ UC IR/Airstream IR Control
Vizi Beam RXONE Master-Slave Set Up
Master-Slave Operation This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector
is the output. The rst unit in the chain (master) will use the female
XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit press the MENU button until “Slave Mode” is
displayed, and press ENTER. Use the UP and DOWN buttons to
scroll to the “Master” setting and press ENTER.
3. After setting the Master unit to the master setting find and set
your desired operating mode.
4. On the slave units press the MENU button until “Slave Mode” is
displayed, and press ENTER. Choose either “Slave 1” or “Slave
2” and press ENTER.
5. The slave units will now follow the Master unit.
Sound Active Mode: This mode allows either single unit or several
units linked together, to run to the beat of the music.
1. Press the MENU button until “Sound State” is displayed, and
press ENTER. Press the UP or DOWN buttons so that “ON” is dis-
played and press ENTER.
2. Press the MENU button until “Sound Sense” is displayed, and
press ENTER. Use the UP and DOWN buttons to adjust the sound
sensitivity. Press ENTER when you have found your desired sensi-
tivity level.
Show Mode: This mode allows either a single unit or several units
linked together, to run one of four shows that you choose.
1. Press the MENU button until “Show Mode” is displayed, and
press ENTER.
2. Press the UP or DOWN buttons to nd your desired show, and
press ENTER.
Vizi Beam RXONE Operation
Loading ...
Loading ...
Loading ...