Loading ...
Loading ...
Loading ...
4. Return deep cleaner to upright posi-
tion. Lower handle and replace reoovery
tank.
5. Raise handle to upright position en-ld
reposition clean solution tank.
To clean floor
Read Before you begin cleaning
instructions on page 9.
Do not use the SteamVac deep clean-
er on hardwood floors.
1. Fill clean solutiorl tank with HOOVER
Bare Floor Cleaner (available at additiorlal
cost if not included with your model)
according to instructions for Figs. 2-10
to 2-16.
Do not use any type of wax with your
SteamVac deep cleaner.
2. Move speed selector to the Lo or HI
position for scrubbing or OFF if
scrubbing is not desired.
3. Dry hands and plug deep cleaner
into a properly grounded outlet.
4. Step on handle release pedal and
lower handle to operating position_ turn
deep cleaner ON,
5, To release solution, press trigger,
Slowly move deep cleaner forward and
backward over area to be <_:learled.
6.To pick Lip dirty solution, release trig-
ger arid slowly _love deep cleaner over
area where solution has just been dis-
persed. Use both forward and reverse
strokes.
7. Empty recovery tank when the motor
sound becomes higher pitched and
there is a loss in suction (see "Automatic
shclt-off'rr Fig 2-6)
8. When finished cleaning, follow "After
cleaning" instrLictions on pages 9-10,
Disconnect deep cleaner from electri-
cal outlet and remove _,ttad_ment from
nozzle. Rinse it in dear w_,te_.Do not
remove plastic screen or foam from
attachment.
B _
A. Powered hand tool has rotating
brushes for extra scrubbing action on
slnall carpet areas, carpeted stairs and
upholstery. Brushes can be removed for
converting to the scrub inodule.
B. Stair/uph01stery nozzle has a built-
in brush to help provide the scrubbing
action some spot,_ may need for
rerT/oval<
C. Scrub module with detachable
scrub pad att_lches to the base of the
powered hand tool (in pl;l_e of brush
modcile), C._n be used to '_crcib stub-
_l_lrn ;zlreas such ;zls s(_ uff _n;zlrks r _trie_
..pills, _nd in hard to reach arenas on
hard .>urface...
Ill
limit
How to attach tools
Disconnect deep cleaner from electri-
cal outlet.
1. Place handle irl upriqht positk;,r_ and
remove h__>se frol]2 r_k,
All tools attach to the hose in the same
rrlanner:
2. Oonnect tool to hose by _qiding it onto
conneLtor until the tab (D) k->cks it
,_ec urely.
Using your thumb, push forward and
up on th÷ latch (E) to remove tool a..
shown.
Before using tool
It may be necessary to remove air from
the system ("prime the purrlp") So the
clean solution will flow to tile tool. Follow
these steps:
1 , Attach tool to hose and turn the deep
cleaner ON.
2.Put the tool on a hard surface or
G
against your hand to block off the suc-
tion.
3. Wait a few seconds (can take up to
1 5 seconds). Then squeeze the trigger
and begin cleaning.
Follow the instructions on pages 12-13
for the appropriate cleaning task.
Attaching scrub module
1. Open the tool door and remove the
powered hand tool.
2. Grasp the sides of the brush module
and lift it froin the base (F).
_, Pull scrub module from deep cleaner
and snap it onto tile base.
Note: It may be necessary to rotate the
scrub module (_) slightly so it will align
properly to the base.
_included with some models
Using the scrub tool
With a little solution, test the scrub
tool on a hidden area before using on
the desired surface. If no surface
change is visible, continue to use as
described below.
FOR LARGE AREAS
1, Fill cle_ln solution tank with HOOVER
Bare Floor Cleaner _ a< cording to
instructions for Figs, 2-10 to 2-16.
2. Hold scrub tool above area to be
cleaned and press trigger to dispense
solution.
3, Release trigger and scrub area with
tool. Pick up dirty solution with
squeegee as ,_hown,
FOR SPOT CLEANING
1, Apply Bare Floor Cleaner _ with the
bpray bottle,
2. Scrub area with tool. Pick up diry
solution vvith SqLleegee as sho_rl.
Continued 4 11
Loading ...
Loading ...
Loading ...