Loading ...
Loading ...
Loading ...
GEAppliances.com
Options
Autosoak
This option beginswith a brief agitation, soaks for a specified period of time, then movesthrough the rest of the cycle automatically. On
some models,this option is located on the CycleSelector knob.
Extra Rinse
When you useextra detergent or bleach to clean heavily soiled clothes,use the Extra Rinseoption to better remove additional residues.
Fabric Softener
Setthis option when adding fabric softener to the washer or to selectthe enhanced PowerRinse.
NOTE:Do not usefabric softener dispensingbollswith this washer. Theydo not work correctly in high efficiencywashers.
Delay Wash
Onsome models, asthe Delay Wash pad isrepeatedly pressed,the delay time setsto 30 minutes, i hour,3 hours, 6 hours, 9 hours, and
back to clear (0 minutes).
Onother models, asthe Delay Wash pad isrepeatedly pressed,the delay time sets to 2 hours, 4 hours, 8 hours, and back to clear (0 hours).
Forall models, ifthe Delay Wash pad ispressedfor 3 seconds, it clears (regardlessof the delay time).
Signal
Usethe Signal pad to change the volume of the end of cycle signal. Pressthe pad until you reach the desired volume or off.
Settings
individual settings for agitation (Soil),water temperature (Tamp), and spin (Spin) can be set from the minimum (lowest in column) to
maximum (highest in column). In general, the higher up the column, the more energy will be used.
My Settings (onsome models)
Asthe cycle selector knob isturned, the Soil,Tamp and Spin settings change to automatic pre-set default settings. Ifyou desire adifferent
setting, pressthe appropriate pad(s).Thenpressand hold the t4y Settings pad for 3 seconds and the washer will "remember" these settings
for that Knob Selection.In the future, when you turn the selector knob to that cycle,your settingswill be automatically recalled. NOTE:Signal
volume cannot be setfor My Settings.
Power
Pressto "wake up" the display. If the display is active, press to put the washer into idle mode.
NOTE:Pressing POWERdoes not disconnect the appliance from the power supply.
Start
PressStart to beginthe cycle.NOTE:Thelid must be closed for the washer to fill and the cycle to start. PressingStart again will Pause the
cycle and the Cycleindicator light will blink.
Tocontinue the cycle, pressStart again or close the lid.if machine is paused more than 24 hours,the cycle will be cancelled. Tostop the
cycle,hold the pad for 3 seconds.If water remains in the machine, select the Drain & Spin cycleto drain tub and spin water out of the
washer tub.
Raisingthe lidwill stop agitation or spin action but does not pause the cycle.
aWash (onsome models)
When the eWash pad is pressed,the cycle changes to its most energy efficient settings and all ofthe e!onitor lights will light to indicate
that the most efficient settings are on. Ifyou change settings,the number of eMonitor lightswill decrease (orincrease)to indicate decreased
or increased energy efficiency settings.
Display (onsomemodels)
The display shows the approximate time remaining until the end of the cycle.
NOTE:Thecycle time isaffected by how long it takes the washer to fill.Thisdepends on the water pressure inyour home.The "smart" timer
"learns"the amount of time it takes to fillyour washer and adjusts the total time accordingly.
In addition, this display will, "scroll" the washer status:
• bALANCING Start of rebalancing cycle to redistribute clothes.Stopsafter rebalancing iscomplete.
• dELAY When Delayed Wash is initiated. Replacedwith estimated time when cycle starts.
• End Endof current cycle.
• FILL Forthe first 45 secondsof afill,the estimated end of cycle time isdisplayed. Forthe rest of the fill time, "FILL"isscrolled
until the fill completes.
• LID Cyclestopped because lid isopen. Closethe lid.
• PAUSE Cyclepaused because the Start/Pause pad was pressedand the washer was setto Pause.PressStart pad again to
restart the cycle.
Indicator lights
Five LEDlights indicate the current washer status moving from left to right as the cycle progresses.
DSM Demand Side Management (onsome models) - When connected to your power company's rate monitoring system, the washer will
automatically delay starting if the rates are high/critical. An "ES"will be displayed and the selected cycle will start after/4 hours or when
the rates drop to low/medium, whichever comes first. If the rates are not high/critical, the selected cycle will start immediately.
Loading ...
Loading ...
Loading ...