Loading ...
Loading ...
Loading ...
STEP 1 - UNPACK REFRIGERATOR
5
Excessive Weight Hazard
Use two or more people to move and install refrigerator.
Failure to do so can result in back or other injury.
REMOVE PACKAGING
Ŷ Remove tape and glue residue from surfaces before
turning on the refrigerator. Rub a small amount of liquid
çìöëöòäóòùèõ÷ëèäçëèöìùèúì÷ëüòøõĤñêèõöàìóèúì÷ë
warm water and dry.
NOTE: Do not use sharp instruments, rubbing alcohol,
ĥäððäåïèĥøìçöòõäåõäöìùèæïèäñèõö÷òõèðòùè÷äóè
or glue. These products can damage the surface of your
refrigerator. For more information, see “Refrigerator
Safety.”
Ŷ Dispose of/recycle all packaging materials.
NOTE: It is normal for the freezer door to be slightly higher
÷ëäñ÷ëè÷òóòé÷ëèæäåìñè÷úëèñ÷ëèõèéõìêèõä÷òõìöĤõö÷
installed. This is designed to ensure the gasket seals properly
once the freezer door is loaded with food.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator
éòõæïèäñìñêòõöèõùìæèåèöøõè÷òæòùèõ÷ëèĥòòõúì÷ë
æäõçåòäõçòõëäõçåòäõç÷òäùòìçĥòòõçäðäêèÊïúäüöóøïï
the refrigerator straight out when moving it. Do not wiggle
òõēúäïîĔ÷ëèõèéõìêèõä÷òõúëèñ÷õüìñê÷òðòùèì÷äöĥòòõ
damage could occur.
Important information to know about glass shelves and
covers:
Do not clean glass shelves or covers with warm water
when they are cold. Shelves and covers may break if
exposed to sudden temperature changes or impact, such
as bumping. Tempered glass is designed to shatter into
many small, pebble-size pieces. This is normal. Glass
shelves and covers are heavy. Use both hands when
removing them to avoid dropping.
CLEAN BEFORE USING
After you remove all of the packaging materials, clean the
inside of the refrigerator before using it. See the cleaning
instructions in “Refrigerator Care.”
INSTALLATION INSTRUCTIONS
WARNING
STEP 2 - REVERSE DOOR SWING
(Optional)
If you want the doors to open from the opposite side you can
reverse the door swing.
Tools Needed:
• Phillips Screwdriver
• Pliers
• T25 Torx Screwdriver (On Some Models)
• 5/16” and 3/8” Wrenches or Adjustable Wrench
1. Unplug refrigerator or disconnect power.
2. Remove base grille, if it is already installed.
3. Remove top hinge cover and top hinge. Lift freezer door o
center hinge and set aside.
4. Unscrew center hinge pin. Keep the plastic washers to use
when reinstalling the door.
5. Lift refrigerator door from bottom hinge, and set aside.
6. Using either a wrench or T25 Torx screwdriver, remove the
center hinge and plastic spacer by unscrewing the center
bolt, loosening the side bolts and sliding the hinge to the
center of the cabinet. Tighten the side bolts.
7. On the opposite side of the cabinet, remove the center
bolt and loosen the side bolts. Slide the center hinge and
spacers behind the side bolts. Reinstall the center bolt and
tighten the side bolts.
A
B
C
D
E
A - Hinge Cover Screw
B - Hinge Cover
C - Hinge Bolts
D - Hinge Pin
E - Door Hinge Hole
AB
C
D
E
A - Plastic Spacer
B - Center Hinge
C - Center Hinge Pin
D - Side Bolts
E - Center Bolt
ENGLISH
Loading ...
Loading ...
Loading ...