Loading ...
Loading ...
Loading ...
Water Pressure
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical
connection.
Recommended Grounding Method
A 115 Volt, 60 Hz., AC onty 15 or 20 amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving onty your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an
extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn the control {Thermostat, Refrigerator
or Freezer Oontret depending on the model) to OFF and then
disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source
and reset the control {Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired setting.
A cold water supply with water pressure of between 30 and
120 psi (207-827 kPa) is required to operate the water dispenser
and ice maker. If you have questions about your water pressure,
see '%reubleshooting" or call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inter valve of the
refrigerator needs to be between 30 and 120 psi (207-827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 - 4t4 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 - 414 kPa):
• Oheck to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the fitter if necessary.
• Allow the storage tank on the reverse osmosis system to refitt
after heavy usage.
• If your refrigerator has a water filter cartridge, it may further
reduce the water pressure when used in conjunction with a
reverse osmosis system. Remove the water filter cartridge.
See "Water Filtration System."
If you have questions about your water pressure, catla licensed,
qualified plumber.
F
Read atl directions carefully before you begin.
IMPORTANT:
• If you turn the refrigerator on before the water line is
connected, turn the ice maker OFR
• All installations must meet tocat plumbing code requirements.
• Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures wilt remain
above freezing.
TOOLS NEEDED: Fiat-blade screwdriver, _W' and _W'open-end
wrenches or two adjustable wrenches, _A" nut driver and dritt bit,
hand drill or etectric drill (properly grounded).
NOTE: Your refrigerator dealer has a kit available with a V4"
f6.35 ram) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or 3A_"
f4.76 ram) saddte valve which reduces water flow and ctogs more
easily.
Remove the Base Grille:
1. Open both doors.
2. Place hands along the ends of the gritle. Push in on the top of
the base grille and putt up on the bottom.
NOTE: Be sure to refasten the Tech Sheet behind the base grille
after cleaning.
Replace the Base Grille:
1. Open both doers.
2. Line up the grille support tabs with the metat clips.
3. Push the gritte firmly to snap it into place.
Loading ...
Loading ...
Loading ...