Loading ...
Loading ...
Loading ...
5. HEALTH AND SAFETY INFORMATION9. BASIC OPERATION
Warning!
● Wear appropriate ear protection. Exposure to noise can lead to hearing loss.
● There is a risk of loose clothing, hair etc., being caught in the rotating spindle of the
power tool.
● Do not touch the bit or areas close to the bit immediately after use; they can still be
extremely hot, causing burns.
- 7 -- 14 -
Warning!
● Dust and swarf
– A correctly fitted dust mask, suitable
for the activity and in accordance to
the relevant standard must be worn.
● Swarf produced by metal drilling is
extremely sharp. Take precautions when
clearing swarf. The burr left on the hole
is also sharp and should be removed
with a suitable tool.
● Always wear safety goggles.
● Drill bit will be hot after use.
9.1 INSTALLING AND REMOVING BITS
– FIG. 4
Note: This product is equipped with an electric
brake.
The drill is fitted with a keyless chuck, this means
that a chuck key is not required to secure the drill or
screwdriver bit.
– Place the drill bit shoulder into the chuck as
far as it will go.
– Tighten the chuck firmly.
Note: Short screwdriver bits need only be inserted
to the depth of the hexagon shank before tightening
chuck by hand.
9.2 ROTATIONAL DRIVE SELECTION –
FIG.5
The forward/reverse drive selector switch
determines the direction of rotation of the drive, i.e.
clockwise or anticlockwise.
To alter the direction of rotation:
– Stop the machine and push switch
to the
left or right.
– When the direction switch is pushed to the left, the drive will rotate clockwise.
– When the switch is pushed to the right, the drive will rotate anticlockwise.
– Before operation, check that the switch is set in the required position. Do not change the
direction of rotation until the driver comes to a complete stop.
– When the driver is not in use move the direction switch to the neutral position (the middle
setting) to lock the trigger out.
Note: Failure to use the neutral position may activate the trigger inadvertently. This inadvertent
operation may cause the driver to become damaged.
Wait for the machine to stop. Unless the machine is fitted with a safety brake; some parts may
continue to move due to momentum. Wait for all parts to stop; then unplug it from the power
supply before making any adjustments, carrying out maintenance operations or just finishing using
the tool.
Remove and check setting tools. Some machinery requires the use of additional tools or keys to
set, load or adjust the power tool. Before starting the power tool always check to make certain they
have been removed and are safely away from the machine.
Prevent unintentional starting. Before plugging any machine in to the power supply, make sure
the switch is in the OFF position. If the machine is portable; do not hold the machine near the
switch and take care when putting the machine down; that nothing can operate the switch.
Carefully select an extension lead. Some machines are not suitable for use with extension
leads. If the tool is designed for use outdoors; use an extension lead also suitable for that
environment. When using an extended lead, select one capable of handling the current (amps)
drawn by the machine in use. Fully extend the lead regardless of the distance between the power
supply and the tool. Excess current (amps) and a coiled extension lead will both cause the cable
to heat up and can result in fire.
Concentrate and stay alert. Distractions are likely to cause an accident. Never operate a power
tool if you are under the influence of drugs (prescription or otherwise), including alcohol or if you
are feeling tired. Being disorientated will result in an accident.
Have this tool repaired by a qualified person. This tool is designed to confirm to the relevant
international and local standards and as such should be maintained and repaired by someone
qualified; using only original parts supplied by the manufacturer: This will ensure the tool remains
safe to use.
5.2 ADDITIONAL SAFETY INSTRUCTIONS FOR DRILL DRIVERS
Important: Draper Tools Limited recommends that this machine should not be modified or used
for any application other than that for which it was designed. If you are unsure of its relative
applications do not hesitate to contact us in writing and we will advise you.
– Power tools shall not be used in potentially explosive atmospheres unless specifically designed
for that purpose.
– Unexpected tool movement due to reaction forces or breakage of inserted tool or reaction bar
may cause injuries.
– Power tools shall be isolated from the energy source before changing or adjusting the inserted
tool.
FIG.5
FIG.4
– Be sure the bit is securely in place before using the driver.
– There is a risk of release of toxic chemicals into the atmosphere when using certain materials.
Always be mindful to use the appropriate personal protective wear to help safeguard against
potential skin contact and dust inhalation. Always consult and follow the material supplier’s
safety guidelines.
O
P
E
N
C
L
O
S
E
++++++
+
+
+++++
+
+++++++
++++++
+
+
++++
++++
+++
+++++
Loading ...
Loading ...
Loading ...