Loading ...
Loading ...
_fcodespermitandaseparategroundingwireis
used,it isrecommendedthataqualifiede_ectrician
determine that the grounding path and wire gauge
are in accordance with toca_ codes.
Do Not ground to a gas pipe.
Check with a qualified electrician if you are not
sure oven is proper_y grounded.
Do Not have a fuse in the neutral or grounding
circuit.
Oven must be connected to the proper eUectdcaU
voUtageand frequency as specified on the
modeU/sedd rating plate. (The model/serial rating
plate is located on the oven door or on the oven
frame.}
[_ Models rated from 7.3to 9.6 kW at 240 volts
(5.5to 7.2 kW at 208 volts) require a separate
@-ampere circuit. Models rated at 7.2 kW and
below at 240 volts (5.4 kW and below at 208
volts) require a separate 30-ampere circuit.
[_ A time-delay fuse or circuit breaker is
recommended.
[_ Connect directly to the fused disconnect (or
circuit breaker box} through flexible, armored
or non-metallic sheathed, copper cable (with
grounding wire}.
[_ Flexible armored cable from appliance should
be connected directly to junction box.
[_ Fuse both sides of the line.
[_ A U.L.qisted conduit connector must be
provided atthe junction box.
[_ Do Not cut the conduit.
Wire sizes and connections must conform with the
rating of the appliance and to the requirements of
the National Electrical Code, ANSI/NFPA 70 -- latest
edition (% See Page 1)and all local codes and
ordinances.
if the house has aluminum wiring, follow the
procedure below.
a.} Connect the aluminum wiring to the copper wire
using special connectors designed and
Underwriters Laboratories-listed for joining
copper to aluminum. Follow the electrical
connector manufacturer's recommended
procedure.
b.} Aluminum/copper connection must conform
with local codes and industry-accepted wiring
practice.
Grasp oven
frame to li_
oven.
(
Use screws to attach
oven to cabinet.
Grasp oven
Reattach side frame to lift
trim. oven.
Remove
trim screws.
Remove side
trim.
Use screws to
attach oven to
cabinet.
Preparation
Excessive Weight Hazard
Use two or more people to move and
install oven.
Failure to follow this instruction can
result in back or other injury.
Important: Use both hands to remove oven
doors.
Do Not use handb or any portion of the front
frame or trim for lifting.
Before moving oven acrossfloor, check that oven
is on shipping base or slide oven onto cardboard
or hardboard.
Do Not remove shipping feet at the front tower
corners of oven.
Remove
oven door.
Remove trim
screws.
match on the hinge
in mocked position =
door free to open
and close
latch on the hinge
position = door
ready for removal
shipping feet.
Turn power supply off. Move oven close to
final position.
Remove and discard shipping materials, tape
and protective film from the oven. Do Not
remove shipping base or shipping feet at the
front bwer corners of oven. The shipping feet
will protect the Jower oven trim unti_ oven is
inserted into cabinet.
, Remove and set aside racks and other parts
from inside oven.
m Completely open oven door. In both back
corners of the door you will see door latches in the
locked position. Rotate both latches forward to the
unlocked position.
Grasp outside edges of door with both hands.
• Begin closing door, atthe moment the door
stops closing, lift and puii door toward you.
, Set door aside on a protective surface.
Pull top of trim
down,
3m Remove trim screws attaching right and
left side trim to oven. Grasp the bottom end of
trim and pull away from oven. Slide top end of
trim downward to remove trim from oven. Take
care not to scratch other surfaces with ends of
trim. Set trim and screws aside on protected
surface.
Page 2
Loading ...
Loading ...