MAINTENANCE AND STORAGE
• Clean fan body and fan blade to avoid discoloration.
• Use a non-abrasive detergent and soft cloth for cleaning.
• DO NOT immerse the fan in water, and never allow water to drip
into the motor housing.
• DO NOT use a gasoline thinner or other chemicals to clean fan.
• For storage, clean fan carefully as instructed and store in it’s
original box. Store fan in a clean, dry place.
TROUBLESHOOTING
PROBLEM SOLUTION
Fan blade does not rotate after • Check to see if plug is inserted into outlet
the fan has been started. • Make sure fan blade is unobstructed and is not touching fan screen.
There is an abnormal sound • Make sure fan blade is inserted on the motor shaft properly and is
when starting the fan. properly seated on the rotor pin.
• Make sure fan blade is not hitting fan guard.
• Check to see if there are burrs on the fan blade.
CAUTION: DO NOT use fan if power cord is damaged. Contact service center for repair instructions.
www.hurricane-fans.com
™
18" Oscillating Wall Mount Fan
Instructions
Supreme Series
D
E
L
A
S
E
R
I
E
S
U
P
R
E
M
O
CAUTION: Read Rules for Safe Operation and Instructions Carefully.
WARNING
1. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk
of electric shock, this plug is intended to fit in a polarized outlet only one way. If plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. DO NOT attempt to defeat this safely feature.
2. To reduce the risk of fire or electric shock, DO NOT use fan with any solid-state speed
control devices.
RULES FOR SAFETY OPERATION
1. Never insert fingers, pencils, or any other object through the grille when fan is running.
2. Disconnect fan when moving from one location to another.
3. Disconnect fan when removing grilles for cleaning.
4. Be sure fan is on a stable surface when operating to avoid overturning.
5. DO NOT use fan in window. Rain may create electrical hazard.
6. Ensure that the fan is switched off from the supply mains before removing the grill.
USER SERVICING INSTRUCTIONS (UL)
1. Grasp plug and remove from the receptacle or other outlet device.
DO NOT unplug by pulling on cord.
2. Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades.
3. Remove fuse carefully. Insert the tip of your tool into fuse slot (close with the terminal),
then pry the fuse gradually and slowly, but not overexert. If fuse feels tight, you can try
again to carefully pry it out little by little. After one side of the fuse has been pried out,
you can remove the fuse entirely.
4. Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
5. Close fuse cover. Slide the fuse access cover on top of the plug
until it is closed.
6. Risk of fire. DO NOT replace attachment plug. Contains a safety device
(fuse) that should not be removed. Discard product if the attachment plug is damaged.
Note:
1. When you replace the fuse, please don’t operate suddenly or overexert, or else the
product may become damaged or cause accident.
2. If the plug does not go into the outlet easily, please make sure you have the plug turned
the right way.
The rules about the cord and plug.
1. This product employs overload protection (fuse). A blown fuse indicates an overload or
short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the
fuse as per the user servicing instructions (follow product marking for proper fuse rating)
and check the products. If the replacement fuse blows, a short-circuit may be present
and the product should be discarded or returned to an authorized service facility for
examination and/or repair.
2. Do not operate any fan with a damaged cord or plug. Discard fan or return to an
authorized service facility for examination and/or repair.
3. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar
coverings. Do not route cord under furniture or appliances. Arrange cord away from
traffic area and where it will not be tripped over.
Loading ...
