SAVE THESE INSTRUCTIONS
2007 © Acuity Lighting Group, Inc., Rev A 08/08/07
RJ521316 INST SHT VW_VP_VC
SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION
INSTALLATION
INSTRUCTIONS
RISK OF FIRE - Lamps are hot. Keep
combustible material away from hot
parts.
TROUBLESHOOTING
CAUTION
If this fixture fails to operate properly, check to
make sure:
• The correct lamp is properly installed.
• The fixture is wired correctly.
• The lamp is not faulty.
• The fixture is grounded correctly.
• The line voltage at the fixture is correct.
Observe lamp manufacturer's recommendations
and restrictions on lamp operations, including but
not limited to ballast type, burning position, and
cycling. Use ANSI rated lamps only.
Maintenance: For optimum performance,
periodically clean reflector and lens with a soft,
damp cloth.
Important: DO NOT use abrasive materials, glass
cleaner or other solvents on lens or paint. Use only
mild, soapy water.
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH,
INJURY, OR SIGNIFICANT PROPERTY DAMAGE
- For your protection, read and follow these warnings
and instructions carefully before installing or maintaining this fixture. These instructions do not attempt to
cover all installation and maintenance situations. If you do not understand these instructions or additional
information is required, contact Lithonia Lighting or your local Lithonia Lighting distributor.
WARNING: RISK OF ELECTRIC SHOCK - To avoid electric shock, serious injury, or death, be certain that
all electrical power is disconnected from the supply branch circuit conductors before installing or main-
taining this fixture. This product must be installed and maintained in accordance with the applicable instal-
lation codes by a person familiar with the construction and operation of the product and the hazards
involved.
WARNING: RISK OF PERSONAL INJURY - This product may have sharp edges. Wear gloves to
prevent cuts or abrasions when removing from carton, handling, installing and maintaining this product.
Lithonia Lighting assumes no responsibility for claims arising out of improper or careless installation or
handling of this product.
IMPORIMPOR
IMPORIMPOR
IMPOR
TT
TT
T
ANT SAFETY INSTRUCTIONSANT SAFETY INSTRUCTIONS
ANT SAFETY INSTRUCTIONSANT SAFETY INSTRUCTIONS
ANT SAFETY INSTRUCTIONS
RISK OF FIRE - Observe lamp
manufacturer’s warnings, recommenda-
tions and restrictions on lamp operation
and maintenance.
WARNINGWARNING
WARNINGWARNING
WARNING
• Do not install a damaged fixture.
• This fixture must be wired in accordance
with the National Electrical Code and
applicable local codes and ordinances.
• Proper grounding is required to ensure
personal safety. Be certain green lead
from the fixture is connected to supply
ground.
• Use code compliant connectors for all
electrical connections.
• ALL work should be done by a qualified
electrician.
• WARNING: NEVER connect or disconnect
any component while power supply is
engaged.
DELIVERY: Upon receipt of fixture and accesso-
ries (packed separately), thoroughly inspect for
any freight damage. All damage should be
reported to the delivery carrier. Do not install
damaged fixtures. Compare the catalog de-
scription listed on the packing slip with the fix-
ture label on the inside of the housing to be sure
you have received the correct merchandise.
IMPORTANT SAFETY
INSTRUCTIONS
WARNINGWARNING
WARNINGWARNING
WARNING
Vapor Tight
Wall, Pendant, Ceiling
Prior to Installation
Read carefully before installing light fixtures. If you do not understand these instructions, please
contact your local Lithonia distributor before installing.
INSTALLATION
LOCATION: This product should be mounted to a non combustible surface only.
WALL MOUNTING
1. Attach the wall box to mounting surface. Pull leads to the box.
2. Make wiring connections described below.
3. Attach the fixture by installing the mounting screws in alternate sequence.
4. For a rain-tight seal, caulk all holes and gaps with silicone caulking compound.
PENDANT MOUNTING
1. Thread the fixture onto the conduit, sealing around the conduit using approved N.E.C. procedures.
CEILING MOUNTING
1. Attach the wall box to mounting surface using the two tab and screws provided.
2. Attach the socket assembly using the two screws accessible by first removing the gasket and the two
socket screws.
WIRING
Caution: Use approved connectors for all electrical connections. Connect fixture to supply wires rated for
at least 90° C.
1. Connect the black fixture lead to the black supply lead.
2. Connect the white fixture lead to the white supply lead.
3. Connect the supply ground to the junction box grounding screw per all applicable codes.
LAMP INSTALLATION AND RE-LAMPING
1. When re-lamping, turn power off at the circuit breaker and allow the fixture to cool adequately.
2. Install the correct lamp (provided). Prior to installing the lamp in the fixture, check to be sure the lamp is of
proper type and wattage. Screw the lamp securely into the socket, back the lamp out one to two turns, then
screws the lamp back in, making sure it is secure. This properly seats the lamp in the socket.
3. Reattach the covers. Be sure that the gasket is firmly seated in the proper channel prior to closing fixture to
maintain weather-tight seal.
4. Re-connect the power.
