SKU Number: 356-9254
13W LED Vapor Tight Light
SLWT012PTDID
Questions, Problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-561-4321
Monday-Friday 8:00a.m. - 5:00p.m. CST
PACKAGE CONTEN TS
HARDWARE CONTENTS
Note: Hardware not shown to size
3 Wire Connectors
®
WARNING:
must be wired in accordance with the National Electrical Code and all
applicable local codes and ordinances. Proper grounding is required to
NOTE:
source. UL approved wire connectors should be used. Be sure no loose
strands of wire are sticking out form under your wire connectors.
WARNING:
SAFETY INSTRUCTIONS FOR SECURITY LIGHT
MOUNTING:
hanging conduit or to a surface using the two tabs.
guard counter-clockwise and lift to remove.
4. Unscrew the glass lens cover by rotating counter-clockwise.
5. DO NOT TOUCH THE LEDS OR CIRCUIT BOARD. Carefully loosen the two screws
holding the LED light to the junction box. Rotate counter-clockwise until it separates
from the junction box.
6. Remove the desired plug in the junction box.
7. Mount the junction box to the surface using the two tabs on the side of the
junction box.
8. Use
wire connectors (included) to make all wiring connections.. Connect the house
g
ground wire, consult a qualied electrician. Use a wire connector(included) to connect
round wire to the light’s bare copper ground wire. If the house does not have a
the black house supply wire to the light’s black wire. Use a wire connector(included) to
connect the white house neutral wire to the light’s white wire.
9. Reassemble the light: Carefully push the wires into the junction box. Align and mount
the LED light to the junction box. Do not pinch any wires.
Rotate clockwise and then
clockwise motion until seated tightly. Align the guard, rotate clockwise, and tighten
the two angled guard screws
10. Apply silicone caulk (not provided) around the perimeter of the junction box where it
contacts the mounting surface for a moisture seal.
11. Turn the power back on at the fuse or circuit breaker box.
1
2
Do not ever point in anyone’s eyes as bright light could damage
sensitive eyes.
SAFE USE:
TROUBLESHOOTING:
SAVE THESE INSTRUCTIONS!
WARNING:
WIRING:
If the light does not work, check the light to be sure you have
wire using a wire connector(included). Connect the ground wire to the
connector(included). Connect the black supply wire to the black xture
bare copper wire. Secure the wire but connections with electrical tape.
SAFETY INSTRUCTIONS FOR LED VAPOR TIGHT LIGHTS
• This prouct may cause interference with radios, cordless phones, or de-
vices which use a wireless remote control, such as televisions. If interfer-
ence occurs move the product away from the device, plug the product
remote control. Complies with Part 15 of FCC.
• Never use light around swimming pools, hot tubs, or saunas.
• Not for use with dimmers or motion sensors.
READ ALL INSTRUCTIONS - WARNING:
• Never operate the lamp with missing glass safety shield.
• This lamp is no intended for use nor safe to use in potentially
atmospheres.
• Do not handle this lamp when standing on wet or damp surfaces or in
water. To reduce the risk of electrial shock, do not remove the ground
wire.
This equipment has been tested and found to comply with the limits
for a consumer device, pursuant to Part 15 of the FCC Rules. Operation
is subject to the following conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment generates, uses, and can radiate frequency energy, and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However , there is no
guarantee that interference will not occur in a particular installation.
Interference problems do occur, please consult the system equipment
owner’s manual for suggestions. Some of those suggestions include
relocation of the computer system away from the television or radio or
FCC WARNING:
FIVE-YEAR LIMITED WARRANTY:
the original sales receipt back to your nearest MENARDS® retail store.
At its discretion, PATRIOT LIGHTING® agrees to have the product or part
free of charge, within the stated warranty period, when returned by the
original purchaser with original sales receipt. This warranty; (1) excludes
expendable parts including but not limited to light bulbs; (2) does not
cover damage that has resulted from abuse or misuse; and (3) does not
cover any losses, labor, injuries to persons/property or costs. This war-
which vary from state to state.
Questions, Problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-561-4321
Monday-Friday 8:00a.m. - 5:00p.m. CST
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
