Loading ...
If the appliance you have purchased is not fitted with a mains power lead a power lead resistant
to a temperature of at least 90℃ must be used.
Otherwise, the electrical safety lf the appliance may be put at risk.
The manufacturer declines all responsibility for damage to persons or things caused by non-
observance of the above prescriptions or by interference with any part of the appliance.
WARNING
Close the cable clamp after making the
electrical connection. Close the
terminal board cover by twisting it down.
Scraper for cleaning the hob
WARNING : The appliance and its accessible parts become hot during use.
Care should be taken to avoid touching heating elements.
Children less than 8 years of age shall be kept away unless continuously supervised.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand
maintenance shall not be made by children without supervision.
WARNING : Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g.
WARNING : Danger of fire: do not store items on the cooking surfaces.
WARNING : If the surface is cracked, switch off the appliance to avoid the possibility of electric shock.
WARNING : A steam cleaner is not to be used.
separate remote-control system.
the hazards involved. Children shall not play with the appliance. Cleaning and user
with a lid or a fire blanket.
WARNING : the appliance is not intended to be operated by means of an external timer or
Cleaning
Turn off the mains to the equipment before carrying out any maintenance and wait for it cool down. We advise
using lukewarm water and detergents to clean enameled elements.Never use abrasive products. Rinse the
glass worktop with water and dry using a soft cloth.
Use sponges or a moist cloth to clean the tops, and remember that water in excess can damage the electric
elements. Clean tough stains using non abrasive detergents, or warm vinegar.
Clean the electric tops using a moist cloth, then lightly oil the the top when it is still warm.
Installation
Electrical connection
Appliances with three-pole cable are set up for operation with alternating current at the voltage and frequency
indicated on the rating plate Look at the connection wiring diagram. The earth conductor is yellow/green. The
connection to the electricity supply must be made by a qualified person and following the regulations in force.
When the appliance is to be installed above a built-in oven, the two appliances must be connected separately.
The supply cable must be so positioned that no point can reach a temperature 50° C higher than ambient
temperature. Also check that the supply system has an effective earth connection and corresponds to the
standards in force and that the breaker can be reached easily when the appliance is installed.
Fitting guidelines
The voltage rating of the hob heating elements is 220-240V .Appliance with three-pole cable are set up for
operation current at the voltage and frequency indicated on the rating plate Look at the connection wiring
diagram.The earth conductor is yellow/green. The connection to the electricity supply must be made be made
by a qualified person and following the regulations in force. When the appliance is to be installed above a
built-in oven,the two apliances must be connected separately, to make it easier to take the appliances out and
for electrical safety.
CONNECTION DIAGRAM
Caution! Voltage of heating
elements 220-240V Caution! In the event
of any connection the safety Wire
must be connected to the E terminal.
Recommended type of
connection lead
①
②
③
④
⑤
For 220-240V earthed one-phase
connection, bridges connect L
terminals and terminals, safety
wire to
E
N
L
①
②
④
⑤
The manufacturer refuses all responsibility if the standards in force are not respected.
TECHNICAL INFORMATION FOR INSTALLATION PERSONNEL:
This appliance must be installed only by authorised personnel and in accordance with the
regulations of Electricity authorities. The wall and bench surfaces must be capable of sustaining tempera-
tures of 95 degrees Celsius. All laminates, fixing adhesive and surfacing
materials should be certified suitable for this temperature.Do not install it near fire hazard
place (like curtain etc).
According to the picture as follows, cut the square hole in bench and place the built-in electric hob in it. Your
hob can be fitted to any worktop with a thickness of 40 to 50 mm.
Inserting and fixing the hob
Before inserting the hob into the work surface, place the adhesive seals around the underside edge. It is
important to fix this gasket evely without gaps or overlapping to prevent liquids from seeping inderneath the
hob.
1. Place the gasket around the bottom edge of the hobs as shown in the illustataion overleaf.
2. Place the hob in the installation opening and push it down so that the hob is resting frimly on the cabinet.
3. Secure the hob in position using the fixing brackets supplied.
a
Worktop
Fixing bracket
Screw
Secure the hob to the underside of the worktop using the fixings provided.Screw one end of
the bracket into the pre-drilled holes in the underside of the hob.The other end of the bracket
should be located underneath the worktop to secure the hob in position.
Note 1 :
Fire resistant material (eg ceramic tiles) is required to 450mm above burner top on the wall or vertical
structures are not permitted within 200 mm from burner.
Note 2:
No overhanging surface or rangehood and exhaust system are permitted within 650 mm above burner tops.
Note 3:
Leave at least 50 mm clearance between the base of the appliance and a combustibile surface.
Never leave the packing components (plastic bags, nails, foamed polystyrene, etc..) within the reach of the
children since they are a source of potential danger.
The hob has a speciaf seal which prevents liquid from entering the cabinet. Follow these instructions to
correctly apply it.
Seal:
Detach the seals from their backing, that the transparent protection still adheres to the seal
itself. Turn over the hob and correctly position seal under the edge of the hob itself, so that
the outer part of the seal itself perfectly matches the outer edge of the hob. Evenly and
securely fix the seal to the hob, pressing it firmly in place.
CLEANING AND MAINTENANCE
-When cleaning do not use cleaning agents with a strong abbrasive effect,such as e.g. scouring powders
containing an abrasive,abrasive compounds,abrasive stones,pumice stones,wire brushes and so on.They
may scratch the hob surface, causing irreversible damage.
-Large spillages that are firmly stuck to the hob can be removed by a special scraper. Be careful not to
damage the ceramic hob frame when doing this.
Caution!
The sharp blade should always be protected by adjusting the cover(just push it with you thumb). Injuries
are possible so be careful when using this instrument-keep out of reach of children.
Appropriate light cleaning or washing products are recommended,such as warm water with a little washing
up liquid or cleaning products for stainless steel sinks .
TROUBLE SHOOTING
Malfunction
Hob doesn't work
Solution
•Check the connection of wires
•Check the fuse and the current limit
There is some smoke
when it is working
•It is normal the first time you use.
•Clean the around the electric hob
and the heating area.
The wire is damaged
•Contact the nearest maintainance
center to change the part.
1-worktop
50mm
564
494
2
1
3
4
5
2-screw
3-bracket
4-hob
5-hob seal
5
8
0
m
m
5
64
m
m
4
94
mm
5
m
10
m
68mm
Recommended installation
Wood block
Ventilation slot ≥ mm30
15
MIN
TERMINAL BOARD
All-poles disconnection must be incorporated in the fixed wiring in accordance with wiring rules and allow
disconnection of the appliance after installation by a switch in the fixed wiring.
650-750mm
5
7
4
6