Loading ...
Loading ...
Loading ...
15
14
FINAL PREPARATION
1. Some stainless steel parts may have a plastic protective wrap which must be peeled off. The interior of the wine
cellar should be washed thoroughly with hot, soapy water, rinsed and wiped dry to remove film residue and any
installation dust or debris before being used. Solutions stronger than soap and water are rarely needed.
2. All stainless steel parts should be wiped with hot soapy water. If buildup occurs, do not use steel wool, abrasive
cloths, cleaners, or powders. If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot,
wet cloths to loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other
metal tool to scrape stainless steel; scratches are almost impossible to remove.
ELECTRICAL CONNECTION
E
lectrical Requirements
A
115 volt, 60 Hz, AC only 15 amp fused electrical supply is required. (A time
d
elay fuse or circuit breaker is recommended.) It is recommended that a
separate circuit, serving only this appliance, be provided.
•ELECTRICAL GROUND IS REQUIRED ON THIS APPLIANCE.
•DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE POWER SUPPLY
CORD GROUND PLUG.
•DO NOT USE AN EXTENSION CORD.
Recommended Grounding Methods
For your personal safety, this refrigeration product must be grounded. This appliance is equipped with a 5’ power
supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a
mating 3-prong grounding type wall receptacle grounded in accordance with the National Electrical Code and local
codes and ordinances. If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of
the customer to exchange the existing receptacle in accordance with the National Electrical Code and applicable local
codes and ordinances. The third ground plug SHOULD NOT, under any circumstances, be cut or removed. All UL listed
refrigerated products are equipped with this type of plug.
WARNING
ELECTRICAL SHOCK HAZARD
Failure to follow these instructions could result in fire or electrical shock.
Grounding type
w
all receptacle
Power Supply
with 3-prong
grounding plug
LIGHT ASSEMBLY REPLACEMENT - 15” W. Models
NOTE: Please contact your local Viking Range
Corporation parts distributor or dealer to order a
new light assembly.
To replace the light, first disconnect the unit’s power
cord. Next, remove both the green ground wire
screw located on the left of the light assembly and
the other screw located on the right of the light assembly with a 5-16” hex head screwdriver. (See drawing). Unplug
the light unit and remove complete light assembly.
To install the new light assembly, screw in the green ground wire screw and the screw located on the right with a 5/16”
hex head screwdriver and plug the light unit in.
Plug
Hex head
screw
Light
assembly
Green
ground wire
Hex head
screw
DANGER
ELECTRICAL SHOCK HAZARD
Failure to to disconnect the power cord when changing the light tube,
could result in fire or electrical shock.
LIGHT TUBE REPLACEMENT - 24” W. Dual Zone Models
NOTE: Please contact your Viking Range Corporation parts distributor or dealer to order new light tubes. Use only
approved replacement light tubes from your dealer or manufacturer.
This product uses two light tubes to illuminate the interior of the wine cellar. There is one light tube located behind the
control housing in the the upper compartment and one light tube attached to the underside of the cabinet divider in
the lower compartment.
Use replacement instructions and drawing from the 15”W. Models for this Dual Zone product.
DANGER
ELECTRICAL SHOCK HAZARD
Failure to to disconnect the power cord when changing the light tube,
could result in fire or electrical shock.
LIGHT TUBE REPLACEMENT - 24” W. Single Zone Models
N
OTE: Please contact your Viking Range Corporation parts distributor or dealer to order new light tubes. Use only
a
pproved replacement light tubes from your dealer or manufacturer.
This product uses two 6-watt light tubes to illuminate the interior
of the wine cellar. The light tubes are very reliable electrical
components, but should either or both light tubes not function
properly, please call your local dealer for replacement light tubes.
To replace the light tube:
•Use a small Phillips head screwdriver to remove the two screws
holding the cover plate over the back section of the light tube.
Set the screws and cover plate aside for re-assembly later.
•Using a small flat-blade screwdriver, gently lever the front section
of the light tube down to allow it to be pulled clear of the light
housing. Disconnect the two insulated electrical connectors from
the cabinet's electrical cable and discard the old light tube.
•Reconnect the insulated electrical connector of the new light tube
to the cabinet's electrical cable connectors. Make sure they are
secure and fully inserted.
•Carefully realign the light tube's electrical terminals back into the rear of the light enclosure channel making sure not
to crimp them. Gently insert the light tube along the length of the light enclosure channel. Press the light tube gently
into the light enclosure channel. Only a small part of the light tube should project below the ceiling of the unit. DO
NOT USE A HAMMER TO FIT THE LIGHT TUBE.
•Place the light tube terminal cover plate back in its original position on the light enclosure's flange. Re-use the original
two screws to secure the cover in place. Plug the unit into the electrical socket. Check to see if the light tubes operate
properly.
Light tube
Connectors
Cover plate
Screws
DANGER
ELECTRICAL SHOCK HAZARD
Failure to to disconnect the power cord when changing the light tube,
could result in fire or electrical shock.
Loading ...
Loading ...
Loading ...