Loading ...
Read Operating Instructions
Please become familiar with all the instructions and
warnings before operating any pneumatic tool.
Visually inspect tool for damage and loose or missing
parts. If the equipment is worn or shows signs of
damage, remove it from service and contact an
authorized Sears service center for repairs.
Always Wear Approved Eye Protection
Impact resistant eye protection should meet or exceed
the standards set forth in ANSI Z87.1, Occupational and
Educational Eye and Face Protection. Look for marking
Z87.1 on your eye protectionto ensure that it is an
approved style.
Hearing Protection is Recommended
Hearing protection should be used when the noise level
exposure equals or exceeds an 8 hour time-weighted
average sound level of 85dBA. Process noise, reflective
surfaces, other tools being operated nearby, all add to the
noise level in a given work area. If you are unableto
determine your noise level exposure, we recommend the
use of hearing protection.
Avoid Prolonged ER3osuretoVibration
Pneumatic tools can vibrate during usa. Prolonged
exposure to vibrationor very repetitive hand and arm
movements can cause injury. Discontinuethe use of any
tool if you experience tingling, numbness, discomfortor
pain in your hands or arms. You should consultyour
physician before resuming use of tool.
150 PSlG Maximum
This tool is designed to operate at an air pressure of 60
to 150 pounds per square inch gauge pressure (150
PSIG) maximum, at the tool. Use of higherair pressure
can and may cause injury.Also, the use of higher air
pressure placas the internal components under loads
and stresses they were not designed for, which could
cause premature tool failure.
NOTE: THE AIR SUPPLY SHOULD BE CLEAN, DRYAND
PREFERABLY LUBRICATED. FOR BEST RESULTS
DRAIN THE MOISTURE FROM YOUR COMPRESSOR
DAILY.
WARNING:
SOME DUST CREATED BYPOWER SANDING, SAWING, GRIND-
ING, DRILUNG, AND OTHER CONSTRUCTION ACTIVFFIES
CONTAINS CHEMICALS KNOWNTO CAUSE CANCER, BIRTH
DEFECTS OR REPRODUCTIVE HARM.SOME EXAMPLES OF
THESE CHEMICALS ARE:
LEAD FROM LEAD-BASED PAINTS
CRYSTALLINE SILICAFROM BRICKS, CEMENTAND
OTHER MASONRY PRODUCTS
ARSENICAND CHROMIUM FROM CHEMICALLY
TREATEDLUMBER
YOUR RISK FROM THESE EXPOSURES VARIES,DEPENDING ON
HOW OFTEN YOU DO THIS TYPE OF WORK. TO REDUCE YOUR
EXPOSURE TOTHESE CHEMICALS, WORK INAWELLVENTI-
LATEDAREAAN DWORK WITH APPROVED SAFETY EQUIPMENT
SUCH AS THOSE DUST MASKS THATARE SPECIALLY DE-
SIGNED TO FILTER OUTMICROSCOPIC PARTICLES.
FULL't'WO YEAR WARRANTY ON CRAFTSMAN
PROFESSIONAL AIR-DRIVE TOOLS
IfthisCraftsmanAir-DriveToolfailstogivecomplete
satisfactionwithintwoyearsfromthe date of
purchase,RETURN IT TO THE NEAREST SEARS
SERVICE CENTER/DEPARTMENT INTHE UNITED
STATES, and Sears willrepairit, freeofcharge. Ifthis
Craftsmantoolisused forcommercialor rental
purposes,thiswarrantyappliesforonly90 daysfrom
the date ofpurchase,Thiswarrantygivesyouspecific
legal rights,and you may also haveotherrightswhich
varyfrom stateto state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman
Estates, IL 60179.
The Craftsman Model 875.204840 Continuous Flow
Grease Gun isdesignedfor both automotiveaswell
as heavy industrial usage.
The Craftsman professionalContinuous Flow Grease
Gun Model 875.204840 is designed to operate at 60 to
150 PSI. Lower pressure will reduce the performance
ofthe tool, while pressure higher than the rated 150
PSI will damage the internal components to the tool.
• Exclusive air piston design assures selfpriming.
• Fully automatic; cycles continuous grease flow
when the trigger is depressed.
• Heavy duty spring for prime retention.
• High pressure performance with 60 to 150 PSI
generated at the compressor allows the tool to
deliver 2400 to 6000 PSI (40:1 ratio) of pressure
into the desired fitting.
Always use clean dry air.Excessive moistureand dirt
willgreatlyreducethe lifeofanyair motor.We
recommendtheinstallationofanin-linefilter-regulator-
lubricator as close tothe toolas possible.
A 3/8" air hose isrequired upto alengthof 8 ft. If
morelength isrequired,a 1/2"air hose shouldbe
connectedto the 3/8" hoseto ensurethe toolhasthe
necessaryair supply.Be sure all hoses and fittings
are thecorrectsize and tightlysecured.
Loading ...
Loading ...
Loading ...