Loading ...
Loading ...
O REMOVE EXISTING DISPOSER
t. Turn O_telectrical power st fuse box or e=rcuitgrea_er.
2 DisCOnnectdraintrapfrom disposer waste discharge tube with adjustable pliers
(_ea Fig 6-1), (Also disconnect dlshwe=;har drainconnection, t| required.)
3. _upport disposer w=thOneh=nd and insert =nOof wrench=tie cr screwdriver
into rightside of one mounting lug on lower mounting ring (see Figure 6-2},
Lift disposer stightiy af_dloosen lower mounting ring_y pushing or pulling
wrench=tie or screwdriver to left until disposer isfree from mounting assembly.
(Disposer m=y be heavy - provide support,)
4, With electrical supply turnedoff turn disposer upside down and remove eleotrt.
cal cover plate (sea Figure 6-3), Loosen green ground screwand remove
wire nuts(see Figure6-4), Disconnect disposerwlres from siectdoel auppiy
wire=,Loosen screw(s) on electrical cramp connectorand remove wires from
disposer,
,.......,,., : ....
• II the new disposer mounting Is the same i_sOldor_e,remove mounting a=seml_y
from disposer (Instruction 3) and go to Ins!;ructlott 7,
. If the newdisposer mounting isdifferent from Ihe ol_ one (or you wish to repta_e
the old =Inkflange) you must compiate Steps 5- (] (below), snd Inatruottone 2.
5, then aontlrtue with Instruction ?,
5. Loosenthree mourting sorews, pry snap ring eft with screwdriver,and r_move
oid mounting assembly (Jee Figure e,5), (Some mounting assembly removal
requires additional tOOlS,)
6. PuShold sink flange up throughsink hole (see Flour= 6,8), Use acrewdriver or
putty knife to scrape air Did putty from edge of Sinkhole.
CLEAN SINK DRAIN LINE
Fattureto clean sink drain tins may resutt in drain fine blockage.
t. Remove P4rap,
2, Wl_hdrain auger, clearall h_rdened waste materiel in horizontal drain line.
tit not dtshwel_her te dO=poser, to Imttructfon 9 t
d
you
are oorlnacting
a
go
O REPARE DISHWASHER DRAIN CONNECTION (IF
APPLICABLE)
The knockout drain plug shoutdonly be removed il you are c_JnneCtir_g
a bu!lt-in dishwasher to the disposer. NOTE; ft the dishwa.',her
¢onnecflon i,_made without removing the #tuO the dishwasher may
ovedfOw,(Coltnedtig¢,s must comply wifh local plumbing ¢odes,)
Remove Knockout Plug
1. Lay disposer on its side arid insert s_:rewdriver into dishwasher iMlet so tip rests
on outer edge of knockout plug
2. Tap end of screwdriver handle wkh h,ttmme_ unti4 me[dad piug break'3 teose
(see Figure 8-t),
3. REMOVE LOOSE KNOCKOUT PLUG FROM INSll3E DISPOSEIq
Attach Dishwaahsr Drain Connector
It your dtshwesi'ter drain hose is 7/8" diameter, g_, to Instruction 9.
If your dishwasher drain hose is nol 718" diameter, you must attach a distlwashor
drain cenRector to the diehwa.sher drain Inlet Follow the iTtstallalion IrlStrliCtions
wtlh the co,inaction k_l. (You will c_nr_ecl the di_,hwa_her drain hose to the
connector in Inst_ctlort 123 3
6-2
i ii i i ,,
8-3 8-4
8-S 8-8
Loading ...
Loading ...
Loading ...