Loading ...
Loading ...
ff codes permit and a separate grounding wire is
used, it is recommended that a qualified electrician
determine that the grounding path and wire gauge
are in accordance with bca[ codes.
Do Not ground to a gas pipe.
Check with a qualified electrician if you are not
sure oven is properly grounded.
Do Not have a fuse in the neutra[ or grounding
circuit.
Oven must be connected to the proper eUectdca[
voUtageand frequency as specified on the
modeU/sedd rating pUate.(The model/serial rating
plate is located on the oven door or on the oven
frame.}
[_ Models rated from 7.3to 9.6 kW at 240volts
(5.5to 7.2 kW at 208volts} require a separate
@°ampere circuit. Models rated at 7.2 kW and
below at 240volts (5.4 kW and below at 208
volts} require a separate 30-ampere circuit.
[_ A time-delay fuse or circuit breaker is
recommended.
[_ Connect directly to the fused disconnect (or
circuit breaker box} through flexible, armored
or non-metallic sheathed, copper cable (with
grounding wire}.
[_ Flexible armored cable from appliance should
be connected directly to junction box.
[_ Fuse both sides of the line.
[_ A U.L.qisted conduit connector must be
provided atthe junction box.
[_ Do Not cut the conduit.
Wire sizes and connections must conform with the
rating of the appliance and to the requirements of
the National Electrical Code, ANSI/NFPA 70 -- latest
edition (% See Page 1) and all local codes and
ordinances.
if the house has aluminum wiring, follow the
procedure below.
a.) Connect the aluminum wiring to the copper wire
using special connectors designed and
Underwriters Laboratories-listed for joining
copper to aluminum. Follow the electrical
connector manufacturer's recommended
procedure.
b.} Aluminum/copper connection must conform
with local codes and industry-accepted wiring
practice.
oven,
|
power
supplycable
I Check oven_ operation.
CC::S:::::::3c
Use screws to attach
oven to cabinet.
Reattach side
trim.
Remove
trim screws.
Remove side
trim,
Grasp oven
frame to lift
oven.
Use screws to
attach oven to
cabinet.
Reattach side
trim,
Remove side
trim,
shipping
feet,
Replac
oven door.
Preparation
Excessive Weight Hazard
Use two or more people to move and
install oven.
Failure to foitow this instruction can
result in back or other injury.
Important: Use both hands to remove oven
doors.
Do Not use handb or any portion of the front
frame or trim for lifting.
Before moving oven acrossfloor, check that oven
is on shipping base or slide oven onto cardboard
or hardboard.
Do Not remove shipping feet at the front tower
corners of oven.
shipping feet.
m Turn power supply off. Move oven close to
final position.
Remove and discard shipping materials, tape
and protective film from the oven. Do Not
remove shipping base or shipping feet at the
front bwer corners of oven. The shipping feet
will protect the [ower oven trim until oven is
inserted into cabinet.
, Remove and set aside racks and other parts
from inside oven.
Remove
oven door.
_ power \
supply cable X
W#_ Remove
_ shipping
feet.
Remove trim
Screws.
Remove
oven doors.
match on the hinge
in locked position =
door free to open
and c[ose
latch on the hinge
position = door
ready for removal
Removetrim screw.
Pu[[trim out.
/
Pull top of trim
down.
m Completely open oven door. In both back
corners of the door you will see door latches in the
locked position. Rotate both latches forward to the
unlocked position.
Grasp outside edges of door with both hands.
• Begin closing door, atthe moment the door
stops closing, lift and puii door toward you.
. Set door aside on a protective surface.
3m Remove trim screws attaching right and
left side trim to oven. Grasp the bottom end of
trim and puil away from oven. Slide top end of
trim downward to remove trim from oven. Take
care not to scratch other surfaces with ends of
trim. Set trim and screws aside on protected
surface.
Page 2
Loading ...
Loading ...