Loading ...
27=1/2"
recessed
height
Single oven
25=3/8" max.
recessed
width
\
29"max_
overall
height
27=3/4"
min.
cutout
height
27"min, ___
cabinet width
-
1=1/2" min.
top of cutout
to underside
of ceuntertep
_
25-1/2"
cutout width
5=I/4" bottom of
cutout to f_oer
Single oven
undercounter
{without cooktop
installed above)
T
27=3/4"
min.
cutout
height
1=I/2"
min,
bottom of
cutout to
top of
cabinet
door
27" min,
cabinet width
25=1/2"
_--- cutout ---:_
width
1" top of cutout
to bottom of
upper cabinet
door
t
32"
bottom of
cutout to
floor
Single oven
Double oven
25=3/e"max.
recessed width
49-1/2"
recessed
height
26=314"
j-
61" max,
overs[[
height
r_
J
49-3/4"
min,
cutout
height
1=1/2" min,
bottom of
cutout to top of
cabinet door
27" ram.
_--- cabinet --_
I [
25=1/2"
_--- cutout --_
width
Double oven
1" top 01 cutout
to bottom of
upper cabinet
door
14=3/4"
bottom
of cutout
to fleer
cabinet -_
2e=li4"mim
cutout depth
23"recessed
oven depth
recessed
oven
oven
J'_ front
Cabinet side view
Your safety and the safety of others are
very imp0rtaet.
We haveprovided many important safety
messagesinthis manualand on your appliance,
Atwayeread and obeyaHsafety messages=
This is the safety alertsymbol.
Thissymboi alertsyou to potentiai hazards
that cankiii or hurtyou and others.
Ati safety messageswiii foiiow the safetyalert
symbol andeitherthe word "DANGER"or
"WARNING".Thesewords mean:
You can be killed or seri0usly injured ifyou don't
follow instructions.
Ati safety messageswiii teli you what the potential
hazardis, tell you howto reducethe chance of
injury, andteti you what can happenif the
instructions are not followed.
important: Observe ali governing codes
and ordinances.
Proper installation isyour responsibility.
Have a qualified technician install this oven.
Oven location should be away from strong draft
areas, such as windows, doors and strong
heating vents.
Cabinet opening dimensions that are shown
must be used. Given dimensions provide
minimum clearance.
Recessed installation area must provide
complete enclosure around the recessed portion
of the oven.
Electrical ground is required. See "Electrical
requirements."
Electrical supply junction box should be located
3 inches maximum below the support surface
when oven is installed in a wall cabinet. Drill a
1°inch minimum diameter hole in the right rear
or left rear corner of the support surface to pass
the appliance cable through to the junction box.
For undercounter installation, it is recommended
that the junction box be located in the adjacent
right or left cabinet. If installing the junction box
on rear wall behind oven, junction box must be
recessed and located in the upper or lower right
or left corner of cabinet.
Oven support surface MUST be solid, [eve[ and
flush with bottom of cabinet cutout.
it isthe customer's responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is
adequate and in conformance with National
Electrical Code, AN81/NFPA 70 E latest edition*,
and nit local codes and ordinances.
Copies of the standards listed may be obtained from:
* National Fire Protection Association
Battervmamh Park
Quincy, Massachusetts 02269
Tool needed:
S
screwdriver
Partssupplied:
4 screws (double oven)
Page 1
Loading ...
Loading ...
Loading ...